INTRODUCTION Thank you for purchasing a MAKINEX product. This manual provides information and procedures to safely operate and maintain the JHT-H Jack Hammer Trolley. For your own safety and protection from injury, carefully read, understand, and observe the safety instructions described in this manual.
PROHIBITED These safety warnings do not eliminate all possible hazards that could occur therefore it is essential to use common sense and to strictly follow any instructions to prevent accidents. JHT-H – User Manual REV0919 Page 2 of 18...
Page 5
WARNING Exhaust gases from this product contain chemicals known to State of California to cause cancer, birth defects or other reproductive harm. WARNING WASH HANDS AFTER HANDLING THIS PRODUCT JHT-H – User Manual REV0919 Page 3 of 18...
There is a safety and information panel provided on the front of the Jackhammer Trolley to alert the user of potential safety risks/hazards. Please read and adhere to all instructions on the Unit. JHT-H – User Manual REV0919 Page 4 of 18...
Do not operate the Jackhammer without wearing the appropriate personal protective equipment and assessing the surrounding area for hazards. WARNING FITTING A JACKHAMMER Tools Required ▪ 17mm spanner ▪ 2mm allen key ▪ 19mm spanner ▪ Pliers JHT-H – User Manual REV0919 Page 5 of 18...
Page 8
1. You should have the parts pictured below: 2. Attach the handle to the frame with two mounting bolts provided. JHT-H – User Manual REV0919 Page 6 of 18...
1. Ensure cable is not kinked anywhere along its length. 2. Tighten retaining screw with pliers. 3. Tighten adjustment screw with 2mm allen key to remove slack from the cable. NOTE: Some slack in the mechanism is normal. JHT-H – User Manual REV0919 Page 7 of 18...
FITTING A HILTI TE1000-AVR JACK AHMMER 1. Adjust trolley to the lowest setting and place object underneath to ensure it is parallel to the ground. 2. Identify correct holes for the TE1000. JHT-H – User Manual REV0919 Page 8 of 18...
Page 11
JHT-H – User Manual REV0919 Page 9 of 18...
Page 12
JHT-H – User Manual REV0919 Page 10 of 18...
Page 13
Position the electrical cord from the Jack Hammer to the indicated positions to guide it away from any crush points. JHT-H – User Manual REV0919 Page 11 of 18...
▪ Adjust brake lever to eliminate free-play. ▪ Lubricate brake lever cable. o Drip light weight oil from the top of the cable so it runs through the cable housing. ▪ Grease the pivot axle. JHT-H – User Manual REV0919 Page 12 of 18...
Transportation charges on product submitted for repair or replacement under this warranty are the sole responsibility of the purchaser. This warranty only applies to the original purchaser and is not transferable. JHT-H – User Manual REV0919 Page 13 of 18...
• Where the specific warranty component (e.g. Jackhammer) is under a Manufacturer’s warranty other than MAKINEX (e.g. Bosch, Hitachi, Makita, Hilti etc), the consumer can either contact MAKINEX or the applicable Manufacturer for repairs where such warranty was registered with that manufacturer at purchase.
TEL +31 (0)6 24881203 or EUROPE +31 (0)6 50841849 EMAIL info@mtools.eu TEL +86 18951118278 CHINA EMAIL sales@makinex.com.cn Or your nearest MAKINEX distributor We have very knowledgeable, experienced staff to assist you with help and advice. JHT-H – User Manual REV0919 Page 15 of 18...
APPENDICES A. BLOCK SETS BREAKDOWN B. JACKHAMMER TROLLEY - HAZARD ASSESSMENT C. SALES AND SPARES APPENDIX A – BLOCK SETS BREAKDOWN JHT-H – User Manual REV0919 Page 16 of 18...