Advertisement
Quick Links
Hilti HIT-RE 100 mortar w/
rebar (as post-installed conn.)
Hilti HIT-RE 100 mortar with rebar
(as post-installed connection)
Injection mortar system
Base material
Concrete
Dry concrete
Installation conditions
Diamond
Hammer
coring
drilling
Service temperature range
Temperature range: -40°C to +80°C (max. long term temperature +50°C, max. short term temperature +80°C).
Approvals / certificates
Description
European technical assessment
a)
All data given in this section according to the approvals mentioned above ETA-15/0883 issue 2016-04-21
04 / 2016
Load conditions
Wet concrete
Static/
quasi-static
Compressed air
drilling
Authority / Laboratory
DIBt
Benefits
- suitable for concrete C 12/15 to
Hilti
C 50/60
HIT-RE 100
- high loading capacity
330 ml foil pack
- suitable for dry and water
(also available
saturated concrete
as 500 ml
- for rebar diameters up to 40 mm
and 1400 ml
foil pack)
- non corrosive to rebar elements
- long working time at elevated
temperatures
Statik mixer
- suitable for embedment length till
3200 mm
Rebar
Other informations
European
CE
Technical
conformity
Approval
No. / date of issue
ETA – 15/0883 / 2016-04-21
Corrosion
tested
2
Advertisement
Related Manuals for Hilti HIT-RE 100
Summary of Contents for Hilti HIT-RE 100
- Page 1 Hilti HIT-RE 100 mortar w/ rebar (as post-installed conn.) Hilti HIT-RE 100 mortar with rebar (as post-installed connection) Injection mortar system Benefits - suitable for concrete C 12/15 to Hilti C 50/60 HIT-RE 100 - high loading capacity 330 ml foil pack...
-
Page 2: Setting Details
Hilti HIT-RE 100 mortar w/ rebar (as post-installed conn.) Materials Reinforcmenent bars according to EC2 Annex C Table C.1 and C.2N. Properties of reinforcement Product form Bars and de-coiled rods Class Characteristic yield strength f or f (MPa) 400 to 600 0,2k ≥... -
Page 3: Setting Instruction
Drill parallel to edge and to existing rebar Where applicable use Hilti drilling aid HIT-HB Drilling aid Fore holes l > 20 cm use drilling aid Ensure that the drill hole is parallel to the existing rebar. - Page 4 Brush 4 times with the specified brush by inserting the steel brush Hilti HIT-RB to the back of the hole (if needed with extension) in a twisting motion and removing it. The brush shall produce natural resistance as it enters the drill hole (brush Ø...
- Page 5 Brush 2 times with the specified brush by inserting the steel brush Hilti HIT-RB to the back of the hole (if needed with extension) in a twisting motion and removing it. The brush must produce natural resistance as it enters the drill hole (brush Ø...
- Page 6 Hilti HIT-RE 100 mortar w/ rebar (as post-installed conn.) Injection preparation Tightly attach Hilti mixing nozzle HIT-RE-M to foil pack manifold. Do not modify the nixing nozzle. Observe the instruction for use of the dispenser. Check foil pack holder for proper function. Insert foil pack into foil pack holder and put holder into dispenser.
- Page 7 Hilti HIT-RE 100 mortar w/ rebar (as post-installed conn.) > 250 mm or overhead application Injection method for drill hole depth Assemble mixing nozzle HIT-RE-M, extension(s) and piston plug HIT-SZ. For combinations of several injection extansions use coupler HIT-VL K. A substitution of the injection extansion for a plastic hose or a combination of both is permitted.
- Page 8 Hilti HIT-RE 100 mortar w/ rebar (as post-installed conn.) Setting the element Before use verify that the element is dry and free of oil and other contaminants. For easy installation insert the rebar slowly twisted into the drill hole until the embedment mark is at the concrete surface level.
- Page 9 Hilti HIT-RE 100 mortar w/ rebar (as post-installed conn.) Drilling diameters Drill bit diameters d [mm] Rebar [mm] Diamond coring Compressed air drill Hammer drill (HD) (CA) Dry (PCC) Wet (DD) 12 (10 12 (10 14 (12 14 (12 16 (14...
- Page 10 Hilti HIT-RE 100 mortar w/ rebar (as post-installed conn.) Basic design data for rebar design according to rebar ETA Bond strength in N/mm² according to ETA – 15/0883 for good bond conditions for hammer drilling, compressed air drilling and diamond coring dry...
- Page 11 Hilti HIT-RE 100 mortar w/ rebar (as post-installed conn.) Pre-calculated values of anchorage length for characteristic steel strength = 500 N/mm For Hammer drilling and Compressed air drilling Concrete Rebar bd,y, α2=0.7 Rd,s 0,min b,min bd,y,α2=1 class [mm] [N/mm [kN]...