Champion Power Equipment 100862 Operator's Manual

Champion Power Equipment 100862 Operator's Manual

Front tine tiller
Table of Contents

Advertisement

OPERATOR'S MANUAL
MODEL #100862
FRONT TiNE TiLLER
REGISTER YOUR PRODUCT ONLINE
at championpowerequipment.com
or visit championpowerequipment.com
READ AND SAVE THiS MANUAL. This manual contains important safety precautions which should be read and understood before operating the product. Failure to
do so could result in serious injury. This manual should remain with the product.
Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice.
Made in China - REV 20191216
Champion Power Equipment, Inc., Santa Fe Springs, CA USA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 100862 and is the answer not in the manual?

Questions and answers

joseph summerhill
January 26, 2025

is there a carburetor adjustment for a 100380 tiller

1 comments:
Mr. Anderson
May 14, 2025

Yes, there is a carburetor adjustment for high altitude operation on the Champion Power Equipment 100380 tiller. It involves selecting the correct high altitude main jet based on the carburetor model code stamped on the side of the carburetor.

This answer is automatically generated

Subscribe to Our Youtube Channel

Summary of Contents for Champion Power Equipment 100862

  • Page 1 This manual should remain with the product. Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice. Made in China - REV 20191216 Champion Power Equipment, Inc., Santa Fe Springs, CA USA...
  • Page 2: Table Of Contents

    TAbLE OF CONTENTS 100862 - FRONT TiNE TiLLER TAbLE OF CONTENTS Cultivating ............Tilling on Slopes ..........introduction ........... Clearing the Tines ..........
  • Page 3: Introduction

    100862 - FRONT TiNE TiLLER iNTRODUCTiON SAFETY DEFiNiTiONS Congratulations on your purchase of a Champion Power Equipment The purpose of safety symbols is to attract your attention to (CPE) product. CPE designs, builds, and supports all of our possible dangers. The safety symbols, and their explanations, products to strict specifications and guidelines.
  • Page 4: Important Safety Instructions

    SAFETY iNSTRUCTiONS 100862 - FRONT TiNE TiLLER iMPORTANT SAFETY iNSTRUCTiONS 6f. If fuel is spilled, do not attempt to start the engine, but move the machine away from the area of spillage and This machine meets voluntary safety standard B71.8 – 1996,...
  • Page 5: Maintenance And Storage

    SAFETY iNSTRUCTiONS 100862 - FRONT TiNE TiLLER Maintenance and Storage 13a. Use shallower depth regulator settings, working gradually deeper with each pass. 1. Check all nuts, bolts, and screws for proper tightness to be 13b. Use slower engine speeds.
  • Page 6: Fuel Safety

    SAFETY iNSTRUCTiONS 100862 - FRONT TiNE TiLLER Fuel Safety When transporting or servicing the tiller: Make certain that the fuel valve is in the OFF position and the DANGER  gasoline tank is empty. GaSolinE anD GaSolinE VaPorS arE hiGhlY Disconnect the spark plug wire.
  • Page 7: Safety Symbols

    SAFETY iNSTRUCTiONS 100862 - FRONT TiNE TiLLER Safety Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product.
  • Page 8 SAFETY iNSTRUCTiONS 100862 - FRONT TiNE TiLLER SYmBol mEaninG Toxic Fumes. The engine exhaust from this product contains chemicals known to cause cancer, birth defects and other reproductive harm. risk of asphyxiation. This engine emits carbon monoxide, an odorless, colorless poison gas. Breathing carbon monoxide can cause nausea, fainting or death.
  • Page 9: Operation Symbols

    10% by volume. This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for 3. Move the choke lever to “ChoKE” position.
  • Page 10: Safety Labels

    3mm corner radius; 2mm safe margin; white to be printed shown in 50% process magenta This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for DANGER outside parties without the explicit consent of Champion Power Equipment.
  • Page 11: Controls And Features

    CONTROLS AND FEATURES 100862 - FRONT TiNE TiLLER CONTROLS AND FEATURES Read this operator’s manual before operating your tiller. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference. Tiller Engine 1. muffler 1.
  • Page 12: Parts Included

    CONTROLS AND FEATURES 100862 - FRONT TiNE TiLLER Parts included accessories hardware Engine Oil (16.9 fl. oz. (500 ml) ........Zip Ties (2)............Oil Funnel ............
  • Page 13: Assembly

    ASSEMbLY 100862 - FRONT TiNE TiLLER ASSEMbLY 5. Place the spring (B) back onto the long pole of the wheel adjust bracket (D). Place the washer (A) onto the long pole of Your tiller requires some assembly. This unit ships from our factory the wheel adjust bracket (D).
  • Page 14: Install The Guard Extension

    ASSEMbLY 100862 - FRONT TiNE TiLLER install the Guard Extension 3. Insert the tine spacer (C) into the end of the inner tine shaft which is already assembled to the unit. Align the holes on the 1. Mount the side guard extensions as shown - slide guard tine spacer (C) with the holes on the inner tine shaft.
  • Page 15: Install Speed Control

    ASSEMbLY 100862 - FRONT TiNE TiLLER 3. Replace the M6 × 20 bolts and tighten with the 5mm hex Recommended Engine Oil Type wrench. 10W-30 5W-30 10W-40 5W-30 Synthetic °F °C -28.9 -17.8 -6.7 15.6 26.7 37.8 48.9 Ambient temperature Add Fuel 1.
  • Page 16: Forward Tine Control Lever

    ASSEMbLY 100862 - FRONT TiNE TiLLER Reverse Tine Control Lever WARNiNG  The reverse tine control lever reverse the rotation of the tines Pouring gasoline too fast through the fuel screen may result in so the tiller can be removed from tight spaces, obstructions or blow back of gasoline at the operator while filling.
  • Page 17: Transport Wheel Height Adjustment

    OPERATiON 100862 - FRONT TiNE TiLLER WARNiNG  Do not attempt to till too deeply too quickly. Gradually work down to deeper tilling depths. Place the Depth Regulator Lever in the “travel” position before starting the engine. This position prevents the tines from touching the ground until you are ready to begin tilling.
  • Page 18: Starting The Engine

    OPERATiON 100862 - FRONT TiNE TiLLER Starting the Engine 6. Pull the starter cord slowly until resistance is felt and then pull rapidly. To help prevent serious personal injury or damage to equipment: WARNiNG  Do not attempt to engage the tines or wheels until you have...
  • Page 19: Operation At High Altitude

    TiLLiNG TiPS AND TECHNiQUES 100862 - FRONT TiNE TiLLER under normal operation: WARNiNG  1. To stop the tines, release all control levers. Operation using the alternative main jet at elevations lower 2. Turn the fuel valve to the “OFF” position.
  • Page 20: Avoid Tilling Soggy, Wet Soil

    TiLLiNG TiPS AND TECHNiQUES 100862 - FRONT TiNE TiLLER Avoid Tilling Soggy, Wet Soil Tilling up and Down Slopes (Vertical Tilling) To keep soil erosion to a minimum, be sure to add enough organic Tilling wet soil often results in large, hard clumps of soil that can matter to the soil so that it has good moisture-holding texture and interfere with planting.
  • Page 21: Loading And Unloading The Tiller

    MAiNTENANCE 100862 - FRONT TiNE TiLLER – While power composting, try swaying the handlebars from side – When going down ramps, walk backward with the tiller to side about 6 in. to 12 in. (15 to 30 cm). This “fishtailing”...
  • Page 22: Tiller Lubrication

    MAiNTENANCE 100862 - FRONT TiNE TiLLER Tiller Lubrication EVErY 5 oPEraTinG hourS After every 10 operating hours, oil or grease the lubrication points — Check motor oil level as described below. Use clean lubricating oil (#30 weight engine oil is suitable) and...
  • Page 23: Checking And Adjusting The Tine Drive Belt Tension

    MAiNTENANCE 100862 - FRONT TiNE TiLLER Checking and Adjusting the Tine Drive belt a. Tine inspection: Tension With use, the tines will become shorter, narrower and pointed. Badly worn tines will result in a loss of tilling depth, and reduced It is important to maintain correct tension on the forward and effectiveness when chopping up and turning under organic matter.
  • Page 24: Belt Tension Adjustment

    MAiNTENANCE 100862 - FRONT TiNE TiLLER Change Forward/Reverse Tine Drive belts 3c. Use pliers to prevent the adjuster from turning and turn the slotted screw located inside the spring clockwise 1. Turn off engine. Engine must cool completely before (viewed from operator’s position) to increase tension on proceeding.
  • Page 25: Engine Cleaning

    MAiNTENANCE 100862 - FRONT TiNE TiLLER Engine Cleaning 7. Remove the forward direction tine belt. Keeping the engine clean will help to ensure smooth operation and prevent damage from overheating. Refer to the Engine Owner’s Manual for engine cleaning service intervals and instructions. Be sure that the muffler is cool before servicing the engine.
  • Page 26: Air Cleaner Maintenance

    MAiNTENANCE 100862 - FRONT TiNE TiLLER NOTiCE NOTiCE   The recommended oil type is 10W-30 automotive oil. We consider the first 5 hours of run time to be the break- in period for the engine. During the break in period we recommend using standard automotive non-synthetic blended 1.
  • Page 27: Spark Plug Service

    TRANSPORTATiON AND STORAGE 100862 - FRONT TiNE TiLLER TRANSPORTATiON AND STORAGE Spark Plug Service Spark plug type: F6RTC/F6TC/F7RTC/F7TC Transport with the fuel valve turned the “OFF” position. Transport or store the engine when it is cool to avoid getting burns or For normal engine operation, ensure the spark plug gap is correct starting a fire.
  • Page 28: Removing From Storage

    SPECiFiCATiONS 100862 - FRONT TiNE TiLLER SPECiFiCATiONS WARNiNG  Fuel is extremely flammable and explosive under certain Tiller Specifications conditions. Keep smoke, fire and spark away from operating site. Model ............
  • Page 29: Parts Diagram

    SPECiFiCATiONS 100862 - FRONT TiNE TiLLER Parts Diagram...
  • Page 30: Parts List

    SPECiFiCATiONS 100862 - FRONT TiNE TiLLER Parts List Part number Description Qty. Part number Description Qty. Clutch Lever 40 100379-041 Axle Bushing 100379-001 100379-042 B Uncork Pin Ø2 x 37 100379-002 Handlebar Grip 42 100379-043.48 Wheel 8" , Yellow Bottom Clutch Lever 100379-003.2...
  • Page 31 SPECiFiCATiONS 100862 - FRONT TiNE TiLLER Part number Description Qty. Part number Description Qty. 83 100379-085 Belt Block Bushing Fixed Plate Connecting 122 100379-124.2 Plate, Black 84 100379-086 Big Belt Block Pole 123 100379-125 Flange Bolt M8 x 20 85 100379-087...
  • Page 32: Engine Parts Diagram

    SPECiFiCATiONS 100862 - FRONT TiNE TiLLER Engine Parts Diagram...
  • Page 33: Engine Parts List

    SPECiFiCATiONS 100862 - FRONT TiNE TiLLER Engine Parts List Part number Description Qty. Part number Description Qty. Hexagon Flange Bolt, M6 33 90547-0205-00 Bearing 90001-0612-01 x 12, Blue White Zinc Engine oil Sensor, W/O 34 37060-Z010120-0001 Cylinder Head Cover 12410-Z440110-00A1...
  • Page 34 SPECiFiCATiONS 100862 - FRONT TiNE TiLLER Part number Description Qty. Part number Description Qty. 62 90684-Z010410-0001 93 90740-Z010510-00A0 Clip Clamp Lower Shield, Blue White Fuel Pipe, Ø4.5 x Ø8.5 63 19340-Z010510-0000 94 90686-Z010710-0001 Zinc x 160 Hexagon Flange Bolt, M6 Rubber Jacket, Ø9.5 x...
  • Page 35: Troubleshooting

    TROUbLESHOOTiNG 100862 - FRONT TiNE TiLLER TROUbLESHOOTiNG Problem Cause Solution Spark plug wire disconnected. Reconnect wire. Engine Throttle Control Lever incorrectly Put lever in START position. set. Fuel tank empty. Add fuel. Choke control (if so equipped) in Move to CHOKE position.
  • Page 36: Difficulty Starting Engine (Recoil)

    TROUbLESHOOTiNG 100862 - FRONT TiNE TiLLER Difficulty Starting Engine (Recoil) Problem Cause Solution There is no enough fuel in fuel tank and Fill fuel, open fuel cock. fuel cock is closed. Air vent in the fuel filler cap is clogged.
  • Page 37: Gasoline Engine: No Power

    TROUbLESHOOTiNG 100862 - FRONT TiNE TiLLER Gasoline Engine: No Power Problem Cause Solution Air in fuel line or fuel line clogged. Exhaust air or dredge fuel line. Main oil flow hole is not adjusted Readjust. properly. In carburetor, needle valve hole and Clean and blow to clear.
  • Page 38: Stops Suddenly When Running

    TROUbLESHOOTiNG 100862 - FRONT TiNE TiLLER Stops Suddenly When Running Problem Cause Solution Fuel is empty. Refill fuel. Carburetor is clogged. Check fuel line and dredge. Float is leaking. Repair. Needle valve is stuck. Dismantle float chamber and eliminate. Spark plug is punctured, or short- Replace spark plug.

Table of Contents

Save PDF