Table of Contents
Advertisement
DURATA IMPULSO
PULSE DURATION
This parameter determines the duration in seconds of an output. The adjustment goes from 0° to 30°
Once you have accessed the menu, press ENTER to change the value, press CANCEL to cancel and insert the desired value and
confirm with ENTER. Note: an output with duration of 0 seconds is a stable type output.
MENU OF USER CODES
TYPE OF USERS
This parameter defines the type of users.
M = Master, possibility to lock the calls from the keyboard, enable commands, query the system.
1 - 5 = User only enabled to enable/disable the associated output from the keyboard or from remote with the phone.
Once you have accessed the menu, press ENTER, with the up and down arrows choose the desired user, then press ENTER again
and insert the desired function (keys 1-5 or key 9 for M) , and confirm by pressing ENTER.
MENU OF USER CODES: PROGRAM THE CODES
Once you have accessed the menu press ENTER,with the up and down arrow keys choose the user you want to change:
- Techical Code: code that can be used to program the system (default: 000000)
- User Code from user 01 to user 12: code that can be used to access the Keyboard to interact with the voice-guided menus when
you are connected over the phone to the dialer, or as a password when using the sms (User 01 code default: 111111)
- Reset Calls: code that can be used to stop a call que. It is possible to insert even just one number.
When receiving a call, have the reset code be preceded and followed by the # (example: #123#).
THEvoice guidance confirms the operation with "CALL QUE INTERRUPTED".
SIM Code: PIN code to be inserted; it must be the same as the PIN code that unlocks the SIM.
Note: if the dialer does not initialize when switched on, do not insist with attempts to start it, so as not to risk permanently locking the SIM
card. Make sure the SIM is unlocked with the pin code.
Once you have accessed the menu, press ENTER to change the code, press CANCEL to cancel the old code.. Insert the new code
and confirm by pressing ENTER.
CONTACT ID MENU
CONTACT ID MENU: IDC EVENTS
With this parameter, you can choose and change all the values of the report codes that concern the events notified by the dialer.
Default values:
Once you have accessed the menu, press ENTER, with the up and down arrow keys, choose the event, press ENTER and press
CANCEL to cancel the existent code and to insert the new code. Press ENTER to confirm.
CONTACT ID MENU: IDC AND SYSTEM NUMBERS
IDC numbers: It is possible to insert 8 telephone numbers to which send the report code
Press ENTER, insert the number, confirm with ENTER, with the up and down arrow keys, choose the next number.
Tel / ID Code: It is possible to assign an ID code for system identification to each telephone no., press ENTER, insert the code,
confirm by pressing ENTER, with the up and down arrow keys choose the next number/code.
CONTACT ID MENU: MAX. ATTEMPTS
With this parameter, you can program how many attempts the modem must make before moving on to the next number. MAX
programmable attempts: 10
CONTACT ID MENU: ANSW. WAIT
With this parameter, you can program the time the dialer waits for an answer during a call MAX programmable time: 50 sec.
CONTACT ID MENU: TONE WIDTH
With this parameter, you can change the width of the DTMF tone. This change must ONLY BE MADE IF THERE ARE PROBLEMS WITH RECEPTION OF
THE GSM SIGNAL. The default setting is 3, it is possible to increase and/or decrease this parameter from 0 to 10. Each variation to this parameter must
be tested with GSM operator used and the device intended for the reception of protocols.
www.amcelettronica.com
line alarm = 130
line tamper = 137
GSM KO = 351
life test = 602
card tamper = 137
(default: 999999)
14
VOXOUT v. 1.2
Hide quick links:
Advertisement
Table of Contents
