Sealey VS8812 Instructions Manual

Sealey VS8812 Instructions Manual

Eobd code reader

Advertisement

INSTRUCTIONS FOR:
EOBD CODE REaDER
MODEL No: VS8812
Original Language Version
VS8812 | Issue 1 27/02/17
© Jack Sealey Limited

Advertisement

Table of Contents
loading

Summary of Contents for Sealey VS8812

  • Page 1 INSTRUCTIONS FOR: EOBD CODE REaDER MODEL No: VS8812 Original Language Version VS8812 | Issue 1 27/02/17 © Jack Sealey Limited...
  • Page 2: Table Of Contents

    VS8812 modeL no: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 3: Safety Precautions And Warnings

    - unlike the continuous monitors, many emissions and engine system components require the vehicle to Original Language Version VS8812 | Issue 1 27/02/17 © Jack Sealey Limited...
  • Page 4: Eobd Readiness Monitors

    This data is optional, and it is defined by a given vehicle make if it's used. mode $07 - request for dtcs (pending) from continuously monitored Systems after a single driving cycle has been performed to Original Language Version VS8812 | Issue 1 27/02/17 © Jack Sealey Limited...
  • Page 5: Using The Scan Tool

    Original Language Version VS8812 | Issue 1 27/02/17 © Jack Sealey Limited...
  • Page 6: Power Supply

    2) from unit of measure screen, use the ScroLL button to select the desired unit of measurement. 3) Press the enter button to save your selection and return to previous menu. unit of measure metric english Original Language Version VS8812 | Issue 1 27/02/17 © Jack Sealey Limited...
  • Page 7 ScroLL button to select Previous menu from the System Setup screen, and press the enter button to return to main Screen. Original Language Version Original Language Version VS8812 | Issue 1 27/02/17 VS8812 | Issue 1 27/02/17 © Jack Sealey Limited © Jack Sealey Limited...
  • Page 8: About

    Led test in the System Setup menu. If the scan tool did not pass this test, there is a problem with the Led lamp. Please contact Sealey tech Support or your local distributor. can’t use the diagnostics function.
  • Page 9: Read Codes

    If the “LInKInG error” is displayed, then there might be problems for the scan tool to communicate with the vehicle. contact Sealey technical Support or local distributor. 7). View a summary of system status (mIL status, dtc counts, monitor status) on screen. Wait a few seconds or press any key for diagnostic menu to come up.
  • Page 10: Erase Codes

    If the codes are not cleared, then an “erase failure. turn Key on with engine off!” message appears. erase codes erase failure. turn Key on with engine off! Press any key to con. Original Language Version VS8812 | Issue 1 27/02/17 © Jack Sealey Limited...
  • Page 11: Data Stream

    3) If the vehicle supports both types of tests, then both types will be shown on the screen for selection. I/m readiness Since dtcs Were cleared this drive cycle Original Language Version VS8812 | Issue 1 27/02/17 © Jack Sealey Limited...
  • Page 12: Vehicle Info

    So it is onLY used to check the emission-related monitors' status. note: this function reads off the real time data of emission-related monitoring systems readiness status every two minutes. once Original Language Version VS8812 | Issue 1 27/02/17 © Jack Sealey Limited...
  • Page 13: Ready Test Mode

    If a “Pending” diagnostic trouble code is causing the Yellow Led to light, it is still possible that the vehicle will be allowed to be tested for emissions. con. I/m readiness mIL Status Misfire Monitor fuel System mon comp. component catalyst mon Htd catalyst Original Language Version VS8812 | Issue 1 27/02/17 © Jack Sealey Limited...
  • Page 14: Scan Tool Mode

    WaRRaNTy: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Sole uK distributor, Sealey Group. 01284 757500 www.sealey.co.uk Kempson Way, Suffolk Business Park, Bury St. edmunds, Suffolk. 01284 703534 sales@sealey.co.uk IP32 7Ar Original Language Version VS8812 | Issue 1 27/02/17 © Jack Sealey Limited...

Table of Contents