Ironton 61457 Owner's Manual

Ironton 61457 Owner's Manual

6 inch benchtop grinder

Advertisement

6 Inch Benchtop Grinder
Owner's Manual
WARNING:
Read carefully and understand all ASSEMBLY AND OPERATION
INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
precautions may result in serious personal injury.
Item #61457
READ & SAVE THESE INSTRUCTIONS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 61457 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Ironton 61457

  • Page 1 6 Inch Benchtop Grinder Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item #61457 READ & SAVE THESE INSTRUCTIONS...
  • Page 2 Thank you very much for choosing an Ironton™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it.
  • Page 3: Table Of Contents

    Table of Contents Intended Use ............................4 Packaging Contents ..........................4 Technical Specifications ........................4 Important Safety Information ....................... 4 Specific Operation Warnings ....................... 6 Grounding .............................. 6 Extension Cords ............................ 7 Main Parts of Benchtop Grinder ......................9 Assembly Instructions .......................... 9 Before Each Use ..........................
  • Page 4: Intended Use

    Intended Use The Ironton 6 Inch Benchtop Grinder is designed for general metal grinding and sharpening. It’s powered by its 1/2 HP, 120V motor operating at 3560 RPM. The benchtop grinder comes with two aluminum oxide wheels, each with an adjustable tool rest with eye shields for safety.
  • Page 5 Cluttered, wet, or dark work areas can result in injury. Using the product in confined work areas may put you dangerously close to cutting tools and rotating parts.  Do not use the product where there is a risk of causing a fire or an explosion; e.g., in the presence of flammable liquids, gases, or dust.
  • Page 6: Specific Operation Warnings

     Disconnect the power/air supply from the product and place the switch in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. ...
  • Page 7: Extension Cords

    receptacle installed by a qualified electrician.  CHECK with a qualified electrician or service person if you do not completely understand the grounding instructions, or if you are not sure the tool is properly grounded. Grounded Tools: Tools with 3-Prong Plugs Tools marked with Grounding Required have a 3-wire cord and 3-prong grounding plug.
  • Page 8 overheating.  Be sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it. Protect your extension cords from sharp objects, excessive heat and damp or wet areas. ...
  • Page 9: Main Parts Of Benchtop Grinder

    Main Parts of Benchtop Grinder Reference Subassembly Grinding Base Power Switch Rest Grinding Wheel Eye Shield Guard Assembly Instructions ⚠WARNING  Remove the benchtop grinder from the carton and examine it carefully. Do no dispose of carton or any packaging material until all parts are examined. ...
  • Page 10 Installing the Spark Guards and Eye Shield Brackets Install the spark guards to the wheel guards of your grinder as shown in Fig. 2. Adjust them to within 1/16 in. of the grinding wheel or other accessory being used. Note: There is a left and right spark guard. Refer to Fig. 2 to ensure that you install them correctly. Installing the Eye Shields Note: There is a left and a right eye shield mounting rod.
  • Page 11 Tip: The eye shields are identical and will fit properly on either side of the grinder; however, it may be necessary to loosen the center hex nut in order to slip the shield over the mounting rod. After you have assembled and installed each eye shield mounting rod to the grinder, attach the eye shields to the rods as shown in Fig.
  • Page 12: Before Each Use

    Ring Testing and Installing Grinding Wheels 1. Suspend the wheel on the arbor but do not tighten the spindle nut. 2. Imagine a vertical line up the center of the wheel. With a hard plastic or wood object, tap the wheel at 45 degrees on each side of the vertical line, 1”...
  • Page 13: Operating Instructions

    Operating Instructions ⚠WARNING  Always wear eye protection.  Only use accessories rated at least equal to the maximum speed marked on the tool.  Do not modify the tool in any way.  Do not wear gloves, jewelry, or loose clothing. ...
  • Page 14: After Each Use

    Note: The workpiece will quickly become heated. Frequently submerge the workpiece in water. If the metal becomes heated so much that it gets blue-colored, it will be too soft to be useful. You must grind off the part that is colored, cool the workpiece and start again. After Each Use ⚠WARNING ...
  • Page 15 Maintain the grinder by adopting a program of conscientious repair and maintenance in accordance with the following recommended procedures. It is recommended that the general condition of any tool be examined before it is used. Keep your tool in good repair. Keep handles dry, clean, and free from oil and grease.
  • Page 16: Troubleshooting

    Troubleshooting Use the table below to troubleshoot problems before contacting service personnel or your local dealer. If the problem continues after troubleshooting, call your local dealer for assistance. Failure Possible Cause Corrective Action Check power source for proper Low voltage. voltage.
  • Page 17 Failure Possible Cause Corrective Action Impurity on surface of wheel. Dress the grinding wheel. Lines on surface of workpiece. Use a holding device to more firmly Workpiece not being held tightly. retain the workpiece. Try wheels with a softer bond or Improper type of grinding wheel.
  • Page 18: Parts Diagram

    Parts Diagram Page 18 of 21...
  • Page 19: Parts List

    Parts List Reference Part Description Quantity Screw Left Cover Outer Flange Inner Flange Grinding Wheel Screw Left Wheel Guard Screw Motor End Bell Ball Bearing Motor Stator Motor Case Motor Rotor Washer Bolt Left Spark Guard Right Spark Guard Eye Shield Washer Bolt Left Adjustable Rest...
  • Page 20: Limited Warranty

    Northern Tool and Equipment Company, Inc. ("We'' or ''Us'') warrants to the original purchaser only (''You'' or ''Your'') that the Ironton product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase.
  • Page 21 Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.com Made in China Page 21 of 21...

Table of Contents