Ironton 45982 Owner's Manual
  1. Manuals
  2. Brands
  3. Ironton Manuals
  4. Grinder
  5. 45982
  6. Owner's manual
Ironton 45982 Owner's Manual

Ironton 45982 Owner's Manual

4-1/2in. angle grinder
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
4-1/2IN. ANGLE GRINDER
OWNER'S MANUAL
WARNING:
Read carefully and understand all ASSEMBLY AND OPERATION
INSTRUCTIONS before operating. Failure to follow the safety rules and other
basic safety precautions may result in serious personal injury.
Item# 45982

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 45982 and is the answer not in the manual?

Questions and answers

Related Manuals for Ironton 45982

Summary of Contents for Ironton 45982

  • Page 1 4-1/2IN. ANGLE GRINDER OWNER’S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item# 45982...

  • Page 2: Intended Use

    Thank you very much for choosing an Ironton product! For future reference, please complete the owner’s record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it.

  • Page 3: Important Safety Considerations

    WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understood by the operator that common sense and caution are factors that cannot be built into this product, but must be supplied by the operator.
  • Page 4 b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.
  • Page 5 WARNING: a) This power tool is intended to function as a grinder, sanding or cut-off tool. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fir and/or serious injury. b) Operations such as wire brushing, or polishing are not recommended to be performed with this power tool.
  • Page 6 p) Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock. Kickback and related warnings Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory.
  • Page 7 Additional safety instructions for abrasive cutting-off operations: a) Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.
  • Page 8 ASSEMBLY 1. SIDE HANDLE AND GUARD Side Handle The side handle can be fitted on either side. Your preferred hand and the operation being performed will determine the correct position. Attaching 1. Firmly attach the side handle in the desired position on the grinder.

  • Page 9: Grinding Disc

    Safety Guard The safety guard should be used at all times whilst operating the angle grinder. Attaching 1. Loosen guard bolt, align tabs and rotate guard to the 2. Tighten guard bolt. required position. Removing 3. Loosen guard bolt. 4. Align tabs on the guard with slots on the guard collar. Remove guard. 2.
  • Page 10 1. Depress and hold spindle lock button. 2. Rotate spindle to locate the lock position. 3. Use pin spanner to loosen the outer 4. Insert the disc flange. 5. Screw the outer flange onto the spindle. Note: the ring on the flange must locate within the hole on the grinding disc.

  • Page 11: Operation

    OPERATION 1. LOCK ON SLIDE SWITCH 1. To turn the grinder on, press down and hold on the rear of the switch (a). Push forward until it locks into place (b). Press down the switch again (c). The tool is now locked on for continuous use. 2.
  • Page 12 2. GRINDING 1. Ensure the workpiece is securely held down. 2. Turn on the angle grinder. 3. Begin grinding your workpiece. The optimum grinding angle is 10-15° to the workpiece. Do not apply excessive pressure. Allow the tool to do the work. This will prevent deep gouging. Page of 16...

  • Page 13: Maintenance

    MAINTENANCE • Maintain your Angle Grinder. It is recommended that the general condition of any Angle Grinder be examined before it is used. Keep your Angle Grinder in good repair by adopting a program of conscientious repair and maintenance. Have necessary repairs made by qualified service personnel.
  • Page 14 DIAGRAM AND PARTS LIST Page of 16...
  • Page 15 ITEM DESCRIPTION ITEM DESCRIPTION Outer flange Washer Grinding wheel Pinion Inner flange Wind board Guard Armature Screw Bearing Output spindle Bearing bush Bolt Screw Woodruff key Stator Screw Switch Spring washer Switch push-button Washer Logo Gear box cover Switch push-pole Bearing Screw Bearing cover...
  • Page 16 WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, •...

Table of Contents