Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for jobmate YT9231
Summary of Contents for jobmate YT9231
-
Page 2: Table Of Contents
CONTENTS Know Your Product....................4 Technical Specifications..................5 Description of Symbols................... 6 Contents of Petrol Line Trimmer................7 General Safety Instructions..................8 Additional Safety Instructions................. 10 Assembly Instructions.................... 11 Operation....................... 13 Starting With A Cold Motor................13 Starting With A Warm Motor ................13 Switching the Motor Off.................. -
Page 3: Know Your Product
KNOW YOUR PRODUCT 1 Trimming head 2 Cutting line 3 Protective cover with screw insert 4 Guide shaft with drive shaft 5 Additional handle 6 On/Off switch 7 Throttle trigger lock 8 Throttle trigger 9 Fastening eye for carry strap 10 Choke lever 11 Starter cord 12 Spark plug connector... -
Page 4: Technical Specifications
TECHNICAL SPECIFICATIONS Motor power 750W Motor type 2-stroke, air-cooled Displacement 25CC No-load speed 7500/min Fuel Petrol/oil mix 40:1 Cutting width 38cm... -
Page 5: Description Of Symbols
DESCRIPTION OF SYMBOLS The rating plate on your tool may show symbols. These represent important information about the product instruction on its use. Denotes risk of personal injury, loss of life, or damage to the tool in case of nonobservance. Use eye protection. -
Page 6: Contents Of Petrol Line Trimmer
DESCRIPTION OF SYMBOLS (CONT.) Keep children at a distance of no less than 15m from the work area. Disconnect from mains power immediately if the power cord becomes damaged. Denotes risk of electric shock. Conforms to relevant standards for electromagnetic compatibility. CONTENTS OF PETROL GRASS TRIMMER 1* Unit 1* Guide shaft... -
Page 7: General Safety Instructions
GENERAL SAFETY INSTRUCTIONS WARNING! Read all safety instructions and operating instructions. Failure to comply with the operating instructions or safety instructions can lead to electric shocks, burns and/or serious injuries. Keep the safety instructions and operating instructions safely for future use. Safety equipment When working with the device, the corresponding plastic protective cover for the ejected at high speed. - Page 8 GENERAL SAFETY INSTRUCTIONS (Cont.) Handling sturdy work shoes, tough work gloves, a protective helmet, a protective mask for the face or protective goggles to protect the eyes and good earplugs or other hearing protection to protect against the noise. 2. Store the device in a safe place. Open the petrol cap slowly in order to release hazards, make sure that you are at least 3 metres from the refuelling area before starting the device.
-
Page 9: Additional Safety Instructions
GENERAL SAFETY INSTRUCTIONS (Cont.) 17. Use the device exclusively for its intended purpose, such as trimming and mowing weeds. 18. Never hold the trimming head above knee height when in operation. 19. Do not use the device if bystanders or animals are in the immediate vicinity. Maintain a minimum distance of 15m between the operator and other persons or animals when mowing. -
Page 10: Assembly Instructions
ASSEMBLY INSTRUCTIONS 1. Assembly of guide shaft (fig. D - E) Loosen the handle screw (A) on the coupling sleeve (B), pull the knob (D), feed the drive axle (C) in and let it latch into place. In doing so ensure that the drive shafts inside the guide shaft mesh together properly (turn the reel head a little if necessary). - Page 11 ASSEMBLY INSTRUCTIONS (Cont.) The carry strap enables ergonomic and safe operation of the motor brush cutter. Hook the carry strap into the fastening eye (fig.G / item 9). Check the ease of movement of all moving parts before commissioning. Check all screws are firmly seated and check all protective devices.
-
Page 12: Operation
OPERATION (Cont.) Operating Instructions Please observe the legal regulations for noise protection - these can vary from region to region. Starting with a cold motor Fill the tank with a reasonable quantity of petrol/oil mix. See fuel and oil. 1. Set the device down on a hard, level surface. “... -
Page 13: Tips For Using Your Petrol Line Trimmer
OPERATION (Cont.) Normal procedure: Release the throttle trigger and wait until the motor has run down to idle speed. The set the on/off switch to “Stop” or “0”. Tips for using your petrol line trimmer Lengthening the cutting line Warning! Do not use any type of metal wire or plastic sheathed metal wire in the cutting line spool. -
Page 14: Maintenance
MAINTENANCE... - Page 15 MAINTENANCE (Cont.) Always switch the device off before maintenance work and remove the connector from the spark plug. Replacing cutting line/cutting line spool be used to help. only the cutting line and not the complete spindle are to be replaced: Remove any cutting line remains from the spool.
- Page 16 MAINTENANCE (Cont.) Sharpening the cutting line cutter The cutting line cutter can become blunt over time. If this should occur then loosen the 2 screws that fasten the cutter to the protective cover. Fasten the cutter in a cutting edge. File in only one direction. Adjusting the carburettor Attention! Adjustments to the carburettor should only be carried out by authorised J2 before any work is done on the carburettor.
-
Page 17: Warranty
WARRANTY POLICY Congratulations on your purchase of Petrol Line Trimmer. In order to get maximum benefit from your new purchase, please be aware of the warranty provisions outlined in this document. 2 YEAR [REPLACEMENT/REPAIR] WARRANTY Your Petrol Line Trimmer is guaranteed for a period of 24 months from the original date of purchase. - Page 18 Mitre 10 or Mitre 10 MEGA store where the product was purchased from, for the warranty to be applicable. Please retain your Proof of Purchase. Only the original owner is covered by the manufacturer’s warranty and must have purchased the product from a Mitre 10 or Mitre 10 MEGA store in New Zealand. What is not covered under warranty? •...
Need help?
Do you have a question about the YT9231 and is the answer not in the manual?
Questions and answers