Batteries And Power; Charging The Battery; User Safety; Personal Safety - DeWalt DCE074R Instructions Manual

EC-Declaration of Conformity
Radio Equipment Directive
DEWALT Rotary Laser
DCE074R, DCE079R, DCE079G
DEWALT hereby declares that the DEWALT Rotary Laser
DCE074R/DCE079R/DCE0709G is in compliance with the
Directive 2014/53/EU and to all applicable EU directive
requirements.
The full text of the EU Declaration of Conformity can be
requested at DEWALT Industrial Tool Co., DEWALT Europe,
DEWALT D-655-10 Idstein, Germany 65509 or is available at
the following internet address: www.2helpU.com.
Search by the Product and Type Number indicated on the
nameplate.
READ ALL INSTRUCTIONS

Batteries and Power

This D WALT rotary laser will accept all D
e
lithium ion batteries, but is built to best resist damage during a
fall when used with the following batteries: All 1.5Ah and 2Ah
D WALT 18 volt lithium ion batteries.
e

Charging the Battery

The battery pack is not fully charged out of the carton. You
need to use a D WALT 18 volt charger to charge the battery
e
pack before you can use the rotary laser.
• Refer to the chart at the end of this manual for compatibility
of chargers and battery packs.
• Be sure to read all safety instructions before using your
charger.

WARNING:
• DO NOT attempt to charge the battery pack
with any chargers other than the ones listed
in this manual. The charger and battery pack are
specifically designed to work together.
• Carefully follow all instructions and warnings on
the battery label and package and accompanying
Battery Safety Manual.
1. Slide the battery pack into the charger as described in the
Battery Safety Manual.
2. Wait until the battery pack is fully charged.
3. Slide the battery pack out of the track.
NOTE: When ordering replacement battery packs, be sure to
include the catalog number and voltage.
DW074_DW079 User Manual - EU - APRIL 2018 - TRANSLATED.indd 29
Installing the 18V D
1. Position the fully-charged 18V D
2. Press and hold down the release button on the battery
3. Slide the battery pack all the way into the track on the side
4. Release the button on the battery pack.
Removing the Battery Pack
1. Press and hold the release button on the battery pack.
2. Slide the battery pack out of the track on the laser.
3. Release the button on the battery pack.
4. To recharge the battery pack, insert it into the charger, as

Storing Battery Packs
WALT 18 volt
e
•
•

User Safety

Personal Safety

•
•
Tool Use and Care
•
•
•
29
WALT Battery Pack
e
release button (Figure 15 ) is facing away from you and
E
to the right.
pack.
of the laser.
described in the Battery Safety Manual.
WARNING: Batteries can explode or leak, and can
cause injury or fire. To reduce this risk, follow the
instructions in the Battery Safety Manual.
The best storage place is one that is cool and dry, and
away from direct sunlight and excess heat or cold.
Long storage will not harm the battery pack or charger.
Under proper conditions, they can be stored for 5 years
or more.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
Stay alert, watch what you are doing, and use common
sense when operating a laser product. Do not use
the tool while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while
operating laser products may result in serious personal
injury.
Use appropriate personal protective equipment,
including eye protection when working in a construction
environment.
Do not use the tool if the switch does not turn it on or
off. Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
Store idle laser products out of the reach of children
and do not allow persons unfamiliar with the laser
product or these instructions to operate the laser
product. Laser products are dangerous in the hands of
untrained users.
Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool, may become hazardous when used
with another tool.
ENGLISH
WALT battery pack so the
e
5/17/2018 12:35:32 PM