Subscribe to Our Youtube Channel
Related Manuals for MERQUIP COSMETAL H2OMY TOP A
Summary of Contents for MERQUIP COSMETAL H2OMY TOP A
- Page 1 Installation, use and maintenance handbook H2OMY TOP A H2OMY TOP WG H2OMY TOP H H2OMY TOP HWG H2OMY IN F H2OMY IN WG H2OMY IN H H2OMY IN HWG COD: 5561399 REV:2 05-2014...
-
Page 2: Before Using The Appliance
MANUFACTURER WATER COOLERS Mod......V ..Hz ..W ..A Freon R134a kg..... Classe APPLIANCE DATA PLATE MADE IN ITALY Model Supply voltage Quantity of cooling gas Class Total absorption 000100 0102 Frequency Serial number Construction year-month CONFORMANCE STATEMENT This appliance has been manufactured with suitable materials for use with drink- ing water. -
Page 3: Removal Of Packaging
BEFORE USING THE APPLIANCE If smoke, unusual smells or strange noises are found coming from the Failure to comply with any of these safety regulations could machine, disconnect it immediately from the socket and contact the lo- cal retailer or technical service assistance. Use of the machine in these Periodically disconnect the machine from the socket and clean the plug PLACE OF INSTALLATION and socket with a dry cloth. -
Page 4: Description Of The Appliance
OPERATOR SIDE DESCRIPTION OF THE APPLIANCE These water coolers were designed to provide large quantities of still and They use a direct cooling system (hermetic ice bank). Two types of water coolers are available: carbonated cold water and hot. Countertop (1) They are easy to use and manufactured using top quality materials, offering Undercounter (2) the utmost hygiene and ease of maintenance. - Page 5 GENERAL VIEW (I) Modello sottobanco - (GB) Undercounter model - (D) Unterbaummodelle -- (F) Modele sous plan - (E) Modelo debajo de mesón OUT AMB OUT HOT OUT WATER OUT SODA FILL ICE BANK IN WATER IN CO2 (I) Modello sottobanco - (GB) Undercounter model - (D) Unterbaummodelle -- (F) Modele sous plan - (E) Modelo debajo de mesón FILL ICE BANK IN WATER...
- Page 6 Operator side Rear side Electrical power supply socket 18 Network voltage warning light Main switch 19 Cold water button Cold water thermostat 20 Button for water at room temperature Mains water inlet 3/4M or ø 8mm 21 Sparkling water button (WG models) CO2 inlet ø...
-
Page 7: Technical Characteristics
TECHNICAL CHARACTERISTICS (GB) WG model (GB) H model (DK) modeller WG modell WG modell WG (GB) HWG model (GB) Undercounter model Undercounter models Modeller under skranken Modeller som står under disken Gulvmodeller ( GB) WG model (GB) F model (DK) model F modell F modell F... - Page 8 H2OMY H2OMY H2OMY H2OMY H2OMY H2OMY H2OMY H2OMY TOP A TOP WG TOP H TOP HWG IN F IN WG IN H IN WG Water production Lt/h 15 (8) 15 (13) 15 (13) 15 (13) 15 (13) 3,96 3,96 (2.11) 3,9 (3,4) 3,96 (3,4) 3,96...
- Page 9 HANDBOOK SECTION II...
-
Page 10: Installation
During connection of the appliance to the mains water supply , all pre -exixting tubes , gaskets joints placed between the appliance and the water mains connection must be replaced with new material to avoid contamination. INSTALLATION POSITIONING THE APPLIANCE Position the appliance in the point of installation, away from sources of or equivalent system). - Page 11 FILL FILL FILL ICE BANK IN WATER FILL ICE BANK FILL ICE BANK IN WATER IN WATER (GB)Under counter models IN WATER Connection to the water mains is done using the T tube provided (8 mm 5.3.1 Water connection diameter) and the A to the mains water supply, all pre-existing tubes, gaskets and joints placed Countertop models: Join elements A, T, E, F, G (Fig.11).
-
Page 12: Electricity Connection
IN CO Warning! Before using the machine proceed with the sanitation (see relative paragraph). STARTING Warning! If the appliance has been laid down or turned upside data plate. Make sure that there is an omnipolar switch above the socket with a minimum contact break of 3 mm protected by fuses of suitable amperage for the down, you should wait at least 8 hours before starting it. - Page 13 (GB)Undercounter models IN CO WATER IN CO WATER SETTING UP THE SPARKLING WATER (WG and HWG models) To start the carbonation device: INSTALLATION OF RECHARGEABLE CYLINDERS ( B-RIC) Press the pushbutton for carbonated water Remove the ø6mm tube from the installation kit and connect it to the pressure reducer R of the rechargeable (B-RIC) cylinder to the IN CO Attention! Screw the pressure reducer cap to the cylinder attachment paying atten-...
- Page 14 19.1 19.2 Attention: to carry out this or any other maintenance operation requiring the machine casing to be opened, use protective gloves to avoid being cut by the sharp edges of the sheet steel...
- Page 15 The quality of the carbonation process also depends on the temperature of CARBONATION DEVICE DRAINAGE the water, which means you should wait for the water cooler to have cooled When installing the appliance, or if the water cooler has no water left inside it, a few air bubbles may enter the carbonation device.
- Page 16 STARTING WITH HOT WATER (H and HWG models) Turn on switch 10. production and storage of water heated to 95°C max. Set the desired temperature on thermostat 23; the temperature can be A special safety system allows for hot water to be dispensed only if both the set from a minimum of 60°C to a maximum of 95°C.
-
Page 17: Routine Maintenance
Maintenance operations should be carried out by 25.2 25.1 ROUTINE MAINTENANCE SUBJECT HOW OFTEN Cleaning the outside of the appliance Clean the external part with a damp cloth, do not use solvents or abrasive detergents. Monthly When the manometer falls Replacing the CO2 cylinders Follow the instructions provided in paragraph 6.2. - Page 18 WATER professional INTERNAL CLEANING/HYGIENIC CLEANING HYGIENIC CLEANING WARNING! Given that the products used for the hygienic cleaning procedure With the help of a pump P, connect the appliance’s water inlet to the contain corrosive acidic and alkaline substances, disposable gloves and container with the disinfecting solution.
- Page 19 professional DRAINING CONNECTION The TOP models have a tray prepared to be pierced and connected to a draining tube. The draining tube passes below the machine. For draining, use a soft silicon tube, with an internal diameter of 4 mm. Pierce the tray at the indicated point, using a 3 –...
- Page 22 Merquip Ltd NZ DISTRIBUTORS 58 Walls Road, Penrose, Auckland 1061 PO Box 13-927 Onehunga, Auckland 1643 Free Phone: 0800 636 0 636 T: 09 636 0 636 F: 09 636 8 636 E: info@merquip.co.nz www.merquip.co.nz...
Need help?
Do you have a question about the COSMETAL H2OMY TOP A and is the answer not in the manual?
Questions and answers