Neolab D-6010 User Manual

Digital hotplate magnetic stirrer

Advertisement

Quick Links

User Manual
Digital Hotplate Magnetic Stirrer
Item N° . D-6010
Users should read this Manual carefully, follow the instructions and procedures, and be aware of the
dangers while using this instrument.

Safety Instructions

Warning!
Read the operating instructions carefully before use the instrument
Ensure that only trained staff work with the instrument
Forbid to heat the substances with low burning point or easy-volatile( hotplate )
Risk of bum!
Caution when touching the housing parts and the heating plate.
The heating plate can reach temperatures of 340° C!
Pay attention to the residual heat after switching off.
Protective ground contact!
Make sure that socket must be earthed (protective ground contact) before use
When work, wear suitable protective clothing to avoid the risk from:
Splashing and evaporation of liquids
Release of toxic or combustible gases.
Set up the instrument in a spacious area on a solid, clean, non-slip, dry and fireproof surface, do not
operate the instrument in explosive atmospheres with hazardous substances or under water.
Gradually increase the speed, reduce the speed if :
The stirring bar breakaway because of too high speed
The instrument is not running smoothly, or container moves on the base plate.
Temperature must always be set to at least 25° C lower than the fire point of the media used.
Beware of hazards due to:
Flammable materials or media with a low boiling temperature
Overfilling of media
Unsafe container
Process pathogenic materials only in closed vessels.
If the case of the stirrer bar is PTFE, please note:
Elemental fluorine, three fluoride and alkali metals will corrode the PTFE and Halogen Alkanes make it expansion
at room temperature. Molten alkali, alkaline earth metals or their solution, as well as the powder in second and
third ethnic of the periodic table of Elements will have chemical reaction with PTFE when temperature reaches
300 – 400° C.
neoLab Migge Laborbedarf-Vertriebs GmbH, Rischerstr. 7-9, 69123 Heidelberg
neoLab Berlin Tel. 030 / 30 87 45-0
Tel. 06221 / 84 42-0
info@neolab.de
www.neolab.de
neoLab München Tel. 089 / 35 61 88 -0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the D-6010 and is the answer not in the manual?

Questions and answers

Summary of Contents for Neolab D-6010

  • Page 1 Elements will have chemical reaction with PTFE when temperature reaches 300 – 400° C. neoLab Migge Laborbedarf-Vertriebs GmbH, Rischerstr. 7-9, 69123 Heidelberg Tel. 06221 / 84 42-0 info@neolab.de www.neolab.de neoLab Berlin Tel. 030 / 30 87 45-0 neoLab München Tel. 089 / 35 61 88 -0...
  • Page 2 • If these operations above are normal, the device is ready to operate. If these operations are not normal, the device may be damaged during transportation, please contact neolab for technical support. neoLab Migge Laborbedarf-Vertriebs GmbH, Rischerstr. 7-9, 69123 Heidelberg Tel.
  • Page 3 I start bit; 7 character bits; I parity bit [straight (even]); 1 stop bit. • Transmission speed:9 600 bit/s • neoLab Migge Laborbedarf-Vertriebs GmbH, Rischerstr. 7-9, 69123 Heidelberg Tel. 06221 / 84 42-0 info@neolab.de www.neolab.de neoLab Berlin Tel. 030 / 30 87 45-0 neoLab München Tel. 089 / 35 61 88 -0...
  • Page 4 Use the instrument in a dry clean room and temperature stable environment. • neoLab Migge Laborbedarf-Vertriebs GmbH, Rischerstr. 7-9, 69123 Heidelberg Tel. 06221 / 84 42-0 info@neolab.de www.neolab.de neoLab Berlin Tel. 030 / 30 87 45-0 neoLab München Tel. 089 / 35 61 88 -0...
  • Page 5 Control accuracy of heating temperature: 1° C • neoLab Migge Laborbedarf-Vertriebs GmbH, Rischerstr. 7-9, 69123 Heidelberg Tel. 06221 / 84 42-0 info@neolab.de www.neolab.de neoLab Berlin Tel. 030 / 30 87 45-0 neoLab München Tel. 089 / 35 61 88 -0...

Table of Contents