DeWalt DWE74911 Original Instructions Manual page 16

EngLIsh
Table Saw Mounting (Fig. G, H)

WARNING: To reduce the risk of injury, turn unit
off, disconnect machine from power source before
assembling the table saw to the table saw stand. An
accidental start-up can cause injury.

WARNING: For your own safety, read and understand the
table saw instruction manual before using. Failure to heed
these warnings may result in personal injury and serious
damage to the table saw and the accessory.
Mounting Steps for the DWE7491/DWE7492 Only
(Fig. A, H)
1. Place the saw, table side down, on a stable, non-
marring surface.
2. Place the stand on top of saw as shown. Align the stand
holes 10 with the saw frame holes.
3. Feed the M8x75 pan head bolts
frame then through the saw frame. Secure with an M8 lock
nut from top and tighten in each of the four hole locations.
4. Lift assembly by stand handle onto kickstand.
Mounting Steps For The DW745 and DCS7485
Only (Fig. G)
1. Place the saw, table side down, on a stable, non-
marring surface.
2. Attach the adaptor brackets
pan head bolts, M6 washers, and M6 lock nuts as shown in
Figure G. Do not tighten fully.
3. Place the stand on top of the saw as shown. Align the stand
holes with the holes in the adapters.
4. Feed the M8x45 pan head bolts
through the adapter hole. Secure with M8 washers and M8
lock nuts.
5. Tighten all fasteners securely.
6. Lift assembly by stand handle onto kickstand.

WARNING: When the adapter brackets are mounted
to the power tool, operate it exclusively on the saw
stand. Without the saw stand, the adapter brackets
mounted with the power tool, does not stand securely
and can tip over.

WARNING: To reduce the risk of personal injury, be sure
the table saw is fully anchored on the stand.

WARNING: To reduce the risk of personal injury, do not
hang objects from the handle. The stand may tip when
downward force is applied.
For additional questions or clarification on the above instructions,
consult an authorised D WALT repair agent.
e
Transporting the Saw on the Stand (Fig. A, I)
Collapsing the Stand for Transport
1. Lifting the stand by the handle, tilt up the stand until the
saw is at a 90 degree angle sitting on the kickstand.
2. Fold the handle-side legs by depressing the handle-side leg
release levers 3 and rotate until locking pin clicks into the
14
through the stand
18
15 to the saw using the M6x40
17 through the stand then
detent . Repeat the operation on the second handle side
16
leg of the stand.
3. Fold the wheel-side legs by rotating the wheel-side leg
release levers 4 with foot (or hand) and rotate until locking
pin clicks into the detent
16

WARNING: That before transportation tool must
be disconnected from mains power supply or the
battery must be removed.

WARNING: To reduce the risk of personal injury, DO NOT
operate the table saw mounted to the stand with the legs
folded and the stand sitting on the ground.

WARNING: Be sure the locking pins have engaged and
the legs are firmly held in place.
To Raise Stand from Collapsed Position
Roll the stand to the workspace. Be sure the area is flat and
stable before attempting to set up the saw and stand.
1. Tilt up the stand until the saw is at a 90 degree angle sitting
on the kickstand.
2. Unfold the handle side legs by depressing leg release levers
and rotate until locking pin clicks into the detent. Repeat for
other handle side leg.
3. Unfold the wheel side legs by rotating leg release levers and
rotate leg until locking pin clicks into the detent. Repeat for
other bottom leg.

WARNING: Be sure that the locking pins have engaged
and the legs are firmly held in place.
4. With all legs locked in their open positions, pull stand
handle toward you and tilt over until all four feet are on
the ground.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
. Repeat with other wheel leg.