DeWalt DWE74911 Original Instructions Manual page 15

Weight
8 M8 Hex head bolts
12 M8 Lock nuts
2 Flat washers
1 Hex key wrench
1 Open end wrench
DWE7491 and DWE7492 saw mounting hardware:
M8x75 Pan head bolts (4)
M8 Lock nuts (4)
M8 Flat washers (4)
DW745/DCS7485 saw mounting hardware:
Adapter brackets (front and rear) (2)
M6 Pan head bolts (4)
M6 Flat washers (4)
M6 Lock nuts (4)
M8 Pan head bolts (4)
M8 Flat washers (4)
M8 Lock nuts (4)
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
DO NOT exceed the weight this stand can hold.
The DWE74911 table saw stand is designed
to support 68 kg safely in a work environment.
DO nOt climb, sit or stand on the stand.
DO nOt drop heavy loads on the table.
Date Code Position (Fig. A)
The date code 19 , which also includes the year of manufacture,
is printed into the housing.
Example:
2018 XX XX
Year of Manufacture
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Axle
1
Wheels
2
Handle-side leg release levers
3
Wheel-side leg release levers
4
Locking pins
5
Legs
6
Handle
7
Handle feet
8
Kickstand
9
Saw mounting holes
10
Intended Use
This table saw stand is designed for use with these table saws:
DW745, DCS7485, DWE7491 and DWE7492. When used with
the DW745 and DCS7485 table saws, the adaptor brackets must
be mounted to the saw prior to placing the saw on the stand.
Do not use this stand with any other tool.
DO nOt use under wet conditions or in the presence of
flammable liquids or gases.
DO nOt let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY
Assembling Stand Frame Halves (Fig. B)
1. Slide smaller tube diameter into opposite tube side as
shown until holes align.
2. Install M6x12 pan head bolts until tight on both sides.
Attaching the Wheels and Axle (Fig. C, D)
1. Attach the axle 1 to the end bracket
pre-drilled holes. Secure axle to end bracket using two
carriage bolts, washers and lock nuts provided.
2. Place the wheels 2 on the axle
washers and lock nuts as shown. Tighten wheel and axle
nuts securely.
Attaching the Kickstand (Fig. E)
Insert the tube plugs into the end of the kickstand tube
12
Be sure that the holes in the tube plugs are in line with the
13
holes 14 in the kickstand tube before inserting the tube plugs.
Align the kickstand holes with the holes on the end bracket. Be
sure the kickstand is pointing up when the stand is in an upright
position. Secure the kickstand with the four M8x75 pan head
bolts and nuts provided as shown.
Attaching the Handle (Fig. F)
Attach the handle with the four M8x75 hex head bolts provided.
Feed the bolts through the handle feet
handle tube 7 and through the gusset holes on the end
bracket. Install four nuts and tighten securely. nOtE: The handle
has two positions to choose from: a compact position and an
easy carry/setup position.
EngLIsh
11 by aligning the
1 and secure with
.
9
8 then through the
13