Table of Contents
Advertisement
18.2. IC7002 (BA5948FPE2) IC 4CH Drive
Pin No.
Mark
I/O
1
IN2
2
PC2
3
IN1
4
PC1
5-8
N.C.
9
PGND1
10
PVCC1
11
D1-
12
D1+
13
D2-
14
D2+
18.3. IC803 (MN101EF16ZXW) MICROPROCESSOR
Pin No.
Mark
I/O
1
PCONT1
O
2
PCONT2
O
3
N.C.
4
FL_DATA /
O
OCD_SDA
5
USB_RST
O
6
FL_CLK /
O
OCD_SCL
7
USB_REQ
8
N.C.
9
N.C.
10
N.C.
11
MMOD (GND)
12
OSC2 (8MHz)
O
13
OSC1 (8MHz)
14
VSS
15
XI (32kHz)
16
XO (32KHz)
O
17
VDD3.3
18
VDD1.8
19
NRST
20
N.C.
21
MMOD0
O
22
TERR
23
VERR
O
24
DAB_PCONT
25
RMT
26
HALT
27
DAB_
DDOWFIC
28
DAB_IRQ
29
BLKCK
30
N.C.
31
CD_MDATA
O
32
STAT
33
CD_MCLK
O
34
USB_SDA
I/O
35
CD_MLD
O
36
USB_SCL
37
VDD18
38
MUTEA
O
39
VSS
Function
I
Motor Driver Input
I
Turntable Motor Drive Signal
("L":ON)
I
Motor Drive (1) Input
-
Traverse Motor Drive Signal
("L"): ON)
-
No Connection
-
Ground Connection (1) for Drive
-
Power Supply (1) for Drive
O Motor Drive (1) reverse - action
output
O Motor Drive (1) forward - action
output
O Motor Drive (2) reverse - action
output
O Motor Drive (2) forward - action
output
Function
Power Control Output 1(Pwr
Sply,Active HIGH)
Power Control Output 2
-
No Connection
FL Data Output / On Chip
Debugger Data
USB Reset Pin
FL CLK Output / On Chip
Debugger Clock
I
USB Interrupt Request
-
No Connection
-
No Connection
-
No Connection
-
Memory mode selection
(Ground connection)
Main Oscillator output (8MHz)
I
Main Oscillator input (8MHz)
-
Micom GND
I
Slow Oscillator input (32KHz)
Slow Oscillator output (32KHz)
-
Voltage supply 3.3V
-
Connect to pin 37
I
MICOM RESET PIN (L: reset)
-
No Connection
Switching Mode
I
Time out error
Verify error
-
No Connection
I
Remote Control Input
I
AC Failure Detect Signal
-
No Connection
-
No Connection
I
CD Subcode Block Clock Input
-
No Connection
CD LSI Command Data
I
CD LSI Status Input
CD LSI Command Clock
USB I2C Data Line
CD LSI Command Load
I
USB I2C Clock Line
-
Power Supply (1.8V)
Analog MUTE Output(L:MUTE
ON)
-
Micom GND
Pin No.
Mark
15
D3-
16
D3+
17
D4-
18
D4+
19
PVCC2
20
PGND2
21-24
N.C.
25
VCC
26
VREF
27
IN4
28
IN3
Pin No.
Mark
40
ASP_CLK
41
ASP_DATA
42
N.C.
43
N.C.
44
N.C.
45
CD_RST
46
N.C.
47
DEMO_SET
48
MODEL_SEL
49
TU_STEREO
50
TU_SDA
51
TU_CLK
52
VOL_JOG1
53
VOL_JOG2
54
TU_TUNED
55
N.C.
56
N.C.
57
N.C.
58
N.C.
59
N.C.
60
N.C.
61
N.C.
62
CRTIMER
63
VSS
64
FL_STROBE
65
CLOSE_L
66
OPEN_H
67
DAB_RST
68
DAB_ TU_RST
69
DAB_ TU_SCL
70
DAB_ TU_SDA
71
N.C.
72
DAB_RX
73
RDS_DATA
74
RDS_CLK
75
DAB_MODE
76
UART_IN
77
UART_OUT
65
I/O
Function
O
Motor Drive (3) reverse - action
output
O
Motor Drive (3) forward - action
output
O
Motor Drive (4) reverse - action
output
O
Motor Drive (4) forward - action
output
-
Power Supply (2) for Driver
-
Ground Connection (2) for Driver
-
No Connection
I
Power Supply terminal
I
Reference Voltage Input
I
Motor Driver (4) Input
I
Motor Driver (3) Input
I/O
Function
O
ASP Sound Processor Serial
Clock Output
O
ASP Sound Processor Serial
Data Output
-
No Connection
-
No Connection
-
No Connection
O
CD LSI Reset Ouput (L: reset)
-
No Connection
I
Demo Mode Setting Input
I
D-Port Select (H: D-Port, L:
Deck)
I/O
Tuner Stereo Signal
I/O
IIC Serial Data for Tuner (PLL
Data I/O)
O
IIC Serial Clock for Tuner (PLL
Clock Output)
I
Jog Input 1
I
Jog Input 2
I/O
Tuner Tuned Signal
-
No Connection
-
No Connection
-
No Connection
-
No Connection
-
No Connection
-
No Connection
-
No Connection
I/O
CR TIMER
-
Micom GND
O
Chip select for FL Panel
O
CD Tray Close Control (Active
L)
O
CD Tray Open Control (Active
H)
-
No Connection
-
No Connection
-
No Connection
-
No Connection
-
No Connection
-
No Connection
I
RDS Data Input
I
RDS Clock Input
-
No Connection
-
No Connection
-
No Connection
SA-PM45PC
Advertisement
Table of Contents
