Table of Contents
Related Manuals for Sun Microsystems SUN-OPM80 Series
Summary of Contents for Sun Microsystems SUN-OPM80 Series
- Page 1 User’s Manual SUN-OPM80 Fiber Optic Power Meter English Table: SUN-UM-TE-OPM002 Version: A/0 All the trademarks mentioned in this manual are registered property of Sun Telecom. The right to interpret this manual is reserved by Sun Telecom.
-
Page 2: Table Of Contents
CONTENTS Overview .....................1 Specifications .....................1 Standard packages ..................2 Components Guide ..................3 Operation and Notes ..................4 Maintenance ....................6 Troubleshooting ..................6 Change Battery ...................7 Quality of Services ..................7... -
Page 3: Overview
Fiber Optic Solutions Provider Overview Sun Telecom’s SUN-OPM80 series optical power meter is a newly developed product to meet the requirement of the market. It intergrades the handheld optical power meter and the intelligent optical power meter in one unit. -
Page 4: Standard Packages
Fiber Optic Solutions Provider Auto Power off Time (min) Operation -10~60 Temperature (° C) -25~70 Storage Temperature (° C) Dimensions (mm) 152(L) x 74(W) x 26(H) Weight (g) Notes: Wavelength Range: Specified standard operating wavelength range in which the Power Meter can work properly under certain technical specifications. -
Page 5: Components Guide
Fiber Optic Solutions Provider Components Guide (1) LCD: λ The LCD screen displays the measurement unit in dB, dBm, nW; the selected wavelength; the current operating situation and so on. (2) ON/OFF Key: Press the key to turn the unit ON or OFF. (3) dB Key: Test the optical power under certain wavelength. -
Page 6: Operation And Notes
Fiber Optic Solutions Provider Turn the Back-light ON or OFF. Operation and Notes 1.1. ON/OFF Press the On/Off key for a few seconds to turn on the unit Press the On/Off key for a few seconds to turn off the unit 1.2. - Page 7 Fiber Optic Solutions Provider displayed on the top right corner. ――― Function Button ――― Plus 0.05 Light ――― Minus 0.05 ――― Store Zero λ ――― Switch Wavelength λ+ Zero ――― Return to the Factory Setting Notes: If any errors or mistakes caused by the user self-calibration operation, please press the “λ+ Zero”...
-
Page 8: Maintenance
Fiber Optic Solutions Provider This value should be close to the one that light source (emitting source) set. If it has wide disparity, please make sure the fiber connection is clean properly or replace another jumper. Press the dB key; the reading 0.00dB will be displayed on the screen. The tested power values will be set to the reference value. -
Page 9: Change Battery
Fiber Optic Solutions Provider No display after Battery is Turn on the unit turning on the unit weak/Others again/Change battery Light interface is Check connector Insensitive display in polluted/ carefully and clean sensor’s interface broken/Display locked Change Battery If you find battery is weak while operating it, please immediately turn the unit off and change a new battery. - Page 10 Fiber Optic Solutions Provider To return a defective product for warranty coverage, contact us for a written authorization. Failure to properly protect the product during shipping may avoid this warranty. We will pay the return transportation fee for products repaired or replace in warranty.
-
Page 11: Fiber Optic Solutions Provider
Fiber Optic Solutions Provider Warranty Registration Card Serial Number: Model Number: Date of Purchase: Company Name: Company Address: TEL: FAX: E-mail: Note: Please fax this note within one month from the date of receiving units. YOUR OPINION Do you have any comments on the quality of this product or the service from www.suntelecom.cn •... - Page 12 SHANGHAI SUN TELECOMMUNICATION CO., LTD. Building No.145, Lane 666 Xianing Road, Jinshan Industrial Zone, Shanghai 201506 China Tel: +86 21 60138638 Fax: +86 21 60138635 - 401 E-mail: ics@suntelecom.cn http: //www.suntelecom.cn...