Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for eKey ekey lock
Summary of Contents for eKey ekey lock
- Page 1 OPERATING INSTRUCTIONS...
-
Page 2: Table Of Contents
English Translation of original instructions ID204/447/0/289 Table of contents General ..................2 Note ..................2 Product liability and limitation of liability ........2 Warranty and manufacturer's warranty .......... 2 Notices, symbols, and abbreviations ..........2 Safety information ................ 3 Life-threatening danger resulting from electricity ......3 Tamper-proofing ................ -
Page 3: General
Warranty and The version of our general terms and conditions in force on the date of manufacturer's purchase shall apply. See http://www.ekey.net. warranty Notices, symbols, and abbreviations NOTICE Denotes additional information and useful tips. -
Page 4: Safety Information
Failure to do so will create a risk of electrocution. resulting from Only certified electricians are authorized to carry out the electrical electricity installation work! Tamper- Mount the ekey lock radio module in a secure internal area. This prevents proofing tampering from the outside. en│3... -
Page 5: Product Description
Product description System overview Fig. 1: Overview of the system 1 Connecting cable from finger scanner to control panel 2 Power supply 3 Control panel 4 Distributor 5 Built-in radio emitting module with antenna 6 Radio path 7 Radio cylinder 8 Lock 9 Finger scanner 4│en... -
Page 6: Scope Of Delivery
□ ekey lock radio module: Scope of delivery Module knob Radio emitting module Short antenna (41 mm) RFID card set (activation, mounting, battery replacement) Two CR2 batteries Battery replacement clamp Self-tapping fillister head screw □ Mechanical knob with permanently assembled cylinder and fixing screw □... -
Page 7: Radio Cylinder
Radio cylinder The radio cylinder is comprised of: □ A sealed, watertight module knob □ A radio emitting module □ A mechanical knob with permanently assembled cylinder in lengths from 30/30 through 70/70 in 5 mm increments or Swiss round cylinder 32.5/32.5 through 72.5/72.5 in 5 mm increments. -
Page 8: Wireless Transponder
1 Status LED Fig. 4: Optical signals on the radio emitting module Wireless The ekey lock wireless transponder is an accessory part of the ekey lock transponder system. Function of the wireless transponder With the ekey lock wireless transponder, you can even open doors that are equipped with the radio cylinder if the ekey finger scanner, the ekey keypad, or the ekey control panel is not operational. -
Page 9: Technical Specifications
Technical specifications Name Unit Values Supply 3 (2 CR2 lithium batteries) Operating temperature °C -20 to +65 Storage temperature °C -40 to +85 Dimensions 40 x 41 Unlock cycles (battery Cycles Up to 70,000 (at 20°) service life) Storage service life Years Wireless transmission (AES128 encryption) - Page 10 Name Unit Values Supply 3 (1 CR2032 lithium battery) Temperature range °C 0 to +70 Number of Approx. 10,000 operations per battery charge Range Max. 5, typical 1 IP code Table 5: Technical specifications: Wireless transponder en│9...
-
Page 11: Installation
Installation ATTENTION Mount and cable the product correctly before connecting power. Possible property damage! Do not connect the grid supply yet! ATTENTION You are not permitted to use the radio cylinder on doors with rosettes or fittings on the outside that can easily be removed. Otherwise, you will not be able to rely on protection against unauthorized opening. -
Page 12: Activation
The devices are activated by connecting the radio cylinder to the ekey devices home/net system in order to set up an operational ekey lock system. The devices can only be activated if you have assembled and cabled the components of the ekey lock radio modules, the mechanical knob with permanently assembled cylinder, and the ekey home/net components. -
Page 13: Use
Opening a The primary purpose of the product is to open doors. The system is in door normal mode. Using the finger scanner Step Action Description Display Swipe a stored finger Status LED lights up green. over the sensor. Status LED lights up red. -
Page 14: Updating The Software
However, malfunctions or defects as a result of external influences or incorrect operation may still occur. ekey has implemented emergency opening solutions which will enable the door to be opened in the event of the following problems:... -
Page 15: Power Failure Or Technical Fault
This may be the case in the event of a power failure or a technical fault. NOTICE The batteries of the module knob must be intact for the wireless transponder to function. - Page 16 Enrolling the wireless transponder You can enroll a wireless transponder for emergency opening. Step Action Description Display Turn the module knob Status LED flashes red. until it flashes red. Status LED Hold the activation card flashes green. in front of the module Low acoustic knob within 5 s.
- Page 17 Deleting wireless transponders You can delete individual wireless transponders that have been enrolled. Step Action Description Display Turn the module knob Status LED flashes red. until it flashes red. Status LED Hold the activation card in flashes green. front of the module knob Low acoustic within 5 s.
-
Page 18: Error Displays And Troubleshooting
If these suggestions fail to solve the problem, the ekey lock radio cylinder must be returned to ekey biometric systems GmbH to be checked. Please ship the equipment in suitable packaging. Improper packaging can lead to the warranty being voided. -
Page 19: Maintenance
Maintenance With the exception of the batteries, the ekey lock radio cylinder is maintenance-free. Batteries Battery management The module knob has a built-in battery management function. This function signals when the battery charge is running low. There are 3 phases. - Page 20 Battery replacement You do not have to remove the module knob from the cylinder in order to replace the battery. Step Figure Description Slide the battery replacement clamp over the module knob. Press down on the two locking bolts on the module knob with the battery replacement clamp.
-
Page 21: Disposal
All content, artwork, and any ideas contained in these operating instructions are subject to applicable copyright laws. Any transmission, relinquishment, or transfer of this content or parts thereof to any third party requires the prior written consent of ekey biometric systems GmbH. Translation of the original documentation. 20│en... - Page 22 Via Copernico, 13/A, I-39100 Bolzano Tel.: +39 0471 922 712 italia@ekey.net ID 204/447/0/289: Version 1, 2015-07-22 Media Center ID: 3010 www.ekey.net Made in Austria ekey biometric systems GmbH operates a quality management system in compliance with EN ISO 9001:2015 and is certified accordingly.
Need help?
Do you have a question about the ekey lock and is the answer not in the manual?
Questions and answers