Related Manuals for Campbell 015ARM
Summary of Contents for Campbell 015ARM
- Page 1 Solar Radiation Sensor Mounts 015ARM, CM225, CM226, CM255, CM255LS, CM260, and CM265 Revision: 9/19 Copyright © 2016 – 2019 Campbell Scientific, Inc.
-
Page 2: Limited Warranty
Limited Warranty “Products manufactured by CSI are warranted by CSI to be free from defects in materials and workmanship under normal use and service for twelve months from the date of shipment unless otherwise specified in the corresponding product manual. (Product manuals are available for review online at www.campbellsci.com.) Products not manufactured by CSI, but that are resold by CSI, are warranted only to the limits extended by the original manufacturer. - Page 3 Campbell Scientific company serves your country. To obtain a Returned Materials Authorization (RMA) number, contact CAMPBELL SCIENTIFIC, INC., phone (435) 227-9000. Please write the issued RMA number clearly on the outside of the shipping container. Campbell Scientific’s shipping address is: CAMPBELL SCIENTIFIC, INC.
- Page 4 Periodically (at least yearly) check electrical ground connections. • WHILE EVERY ATTEMPT IS MADE TO EMBODY THE HIGHEST DEGREE OF SAFETY IN ALL CAMPBELL SCIENTIFIC PRODUCTS, THE CUSTOMER ASSUMES ALL RISK FROM ANY INJURY RESULTING FROM IMPROPER INSTALLATION, USE, OR MAINTENANCE OF TRIPODS, TOWERS, OR ATTACHMENTS TO TRIPODS AND TOWERS SUCH AS SENSORS, CROSSARMS, ENCLOSURES, ANTENNAS, ETC.
-
Page 5: Table Of Contents
CM255 mounted level and at an angle ..........2 6-1. Solar sensor placement .................5 6-2. Mounting hole locations for solar sensors ..........6 6-3. 015ARM and CM255 showing U-bolt mounting .........7 6-4. CM255LS .....................8 6-5. CM226 showing horizontal and vertical mount options ......9... -
Page 6: Introduction
This mount includes the leveling base required by smaller sensors such as the Apogee CS301. The 015ARM mounts to a vertical mast or tripod. The CM225 and CM226 are designed to be mounted either horizontally to a crossarm or vertically to a mast or a pole to keep the mounting plate level. -
Page 7: Precautions
With the 015ARM, the sensor is mounted away from the vertical pipe, allowing for a more unobstructed view of the sky. The CM255 and CM255LS may be mounted at different angles, depending on the user’s needs (FIGURE 4-1). -
Page 8: Specifications
Compatible Sensors Mounts to Consists of a square platform, mounting arm, and mounting CS300 , LI200X tripod or tower 015ARM hardware. Platform LI200S , LI190R mast or user- area is 15.2 x 15.2 cm LI190SB , CMP3, supplied pipe with Solar Sensor (6.0 x 6.0 in), arm... - Page 9 1.50 kg (3.30 lb) for –V. Retired sensors may also be compatible. Contact Campbell Scientific for more information. A leveling base is required to mount the CS300, LI200X, LI200S, LI190R, or LI190SB. Assumes the CMP6, CMP11, and CMP21 are not housed in the CVF4 Heater/Ventilation Unit.
-
Page 10: Installation
Solar Radiation Sensor Mounts Compliance CM225: View EU Declaration of Conformity at: www.campbellsci.com/cm225-solar-mount Installation Siting The solar radiation sensor is usually installed horizontally, but can also be installed at any angle including an inverted position. In all cases, it will measure the flux that is incident on the surface that is parallel to the sensor surface. -
Page 11: Installation
Secure the mounting bracket to the crossarm or the vertical pole using the hardware included with the mounting bracket. The 015ARM, CM225, CM255, CM260, and CM265 use one or two U-bolts, nuts, flat washers,... -
Page 12: 015Arm And Cm255 Showing U-Bolt Mounting
Solar Radiation Sensor Mounts FIGURE 6-3. 015ARM and CM255 showing U-bolt mounting... -
Page 13: Cm255Ls
Solar Radiation Sensor Mounts The CM255LS bracket (FIGURE 6-4) uses two set screws to secure the crossarm or the pole in the channel at the base of the bracket. For pyranometers mounted horizontally, ensure the mounting bracket is horizontal in two dimensions. For pyranometers to be mounted at an angle with the CM255 or CM255LS, set the mounting bracket angle to the desired angle prior to tightening the mounting hardware. -
Page 14: Maintenance
Solar Radiation Sensor Mounts Adjustment screw Crossarm Bolt Wing nut Flat washer Mast Lock washer Horizontal mount Vertical mount FIGURE 6-5. CM226 showing horizontal and vertical mount options Verify all mounting hardware is firmly tightened, and that the mounting bracket is at the desired angle. The CM255LS includes leveling bolts for additional adjustment of the pyranometer level. - Page 15 INFO Global Sales & Support Network A worldwide network to help meet your needs Australia Costa Rica Southeast Asia Garbutt, QLD Australia San Pedro, Costa Rica Bangkok, Thailand Location: Location: Location: 61.7.4401.7700 506.2280.1564 66.2.719.3399 Phone: Phone: Phone: info@campbellsci.com.au info@campbellsci.cc thitipongc@campbellsci.asia Email: Email: Email:...
Need help?
Do you have a question about the 015ARM and is the answer not in the manual?
Questions and answers