6265/6265i/6268 (RM-66) Disassembly Contents Page Safety Information ............................3 ESD Protection ............................. 3 Disassembly Instructions ..........................4 1. Place Protective Film on the A-cover ....................4 2. Remove the Battery Cover ........................4 3. Remove the Antenna/E-cover ......................5 4. Remove the Camera Gasket ......................... 5 5.
6265/6265i/6268 (RM-66) Disassembly Disassembly Instructions 1. Place Protective Film on the A-cover Gently place protective film on the A-cover to prevent scratches during servicing. 2. Remove the Battery Cover a. Turn the mobile terminal off by pressing and holding the End key.
6265/6265i/6268 (RM-66) Nokia Customer Care Disassembly 3. Remove the Antenna/E-cover a. Using the SRT-6 opening tool, gently pry the E-cover from the D-cover, starting at the lower left corner as shown below. b. Continue by sliding the tool along the same side to the top corner of the E-cover.
6265/6265i/6268 (RM-66) Disassembly 5. Remove the Screws a. Slide the mobile terminal into the open position and remove the screw caps located on the back of the slide assembly. b. Undo the two IP-4 Torx 4 Plus screws that retain the assembly.
6265/6265i/6268 (RM-66) Nokia Customer Care Disassembly 6. Remove the A-cover from the B-cover a. With the mobile terminal slide in the open position, open the SD media door. b. Using the SRT-6 opening tool, gently pry the A-cover from the slide mechanism.
6265/6265i/6268 (RM-66) Disassembly 7. Remove the A-cover Keymat Grasp the A-cover with the inside facing you. Using gentle pressure, unsnap the keymat from its retainers. 8. Remove the Mini SD Door a. Push the SD Door upwards and away from you.
6265/6265i/6268 (RM-66) Nokia Customer Care Disassembly 9. Remove the Screws Using a Torx T-6 screwdriver, undo and remove the four T-6 screws that retain the assembly. Note: Do not reuse the screws. Discard and replace with new screws for reassembly.
6265/6265i/6268 (RM-66) Disassembly 11. Remove the PWB With the mobile terminal slide in the open position, use the SRT-6 opening tool to gently loosen the two snaps and the flex connector holding the PWB in place. 12. Remove the Camera a.
6265/6265i/6268 (RM-66) Nokia Customer Care Disassembly Keymat Removal ONLY For servicing that requires removal of the KEYMAT ONLY, follow the instructions below. Disassembly of the mobile terminal is not required for keymat removal. a. If keys are damaged or missing and only keymat removal is required, use the SRT-6 opening tool to gently lift the keymat from its position.
6265/6265i/6268 (RM-66) Disassembly 14. Remove the Main Flex Assembly a. Using an IP-4 Torx 4 Plus screwdriver, undo the four IP-4 Torx 4 Plus screws that retain the main flex assembly to the slide assembly. Note: Do not reuse screws. Discard and replace with new screws for reassembly.
6265/6265i/6268 (RM-66) Nokia Customer Care Disassembly d. Open the slide assembly to align the UI flex cable slots. Gently pull the upper main flex assembly and the UI flex cable from the side assembly. 15. Remove the LCD Flex Cable and Assembly a.
6265/6265i/6268 (RM-66) Disassembly e. Rotate the upper UI PWB to remove it from the LCD frame. f. Holding the LCD frame in both hands, pull the sides outwards and press under the frame to remove the LCD. 16. Remove the Volume Key Using tweezers, gently pull the volume key from its retaining pins, away from the IHF assembly.
6265/6265i/6268 (RM-66) Nokia Customer Care Disassembly 17. Remove the Camera Key Gently free the camera key from its mount using tweezers. 18. Remove the IHF Assembly Grasp the D-cover with the inside facing you. Gently pull toward the top of the D-cover to release the clips and rotate the IHF assembly to free it from the D-cover.
6265/6265i/6268 (RM-66) Disassembly 19. Remove the BT Antenna Using tweezers, gently remove the BT antenna from the D-cover. Note the snap located just above the vertical tab. Snap above veritcal tab Caution: Do not damage the metal antenna springs. 20. Remove the Camera Flash Using tweezers, gently release the flash mounting tab and lift the camera flash from its retainer.
6265/6265i/6268 (RM-66) Nokia Customer Care Disassembly 21. Remove the DC Jack Using a CA-44 adaptor, plug into the DC jack and gently lift it from the D-cover assembly. Make sure the adapter is not plugged into an electric source. CA-44 adaptor 22.