Download Print this page

Advertisement

Quick Links

EN Instructions for use / assembly instructions
DE Gebrauchsanleitung / Montageanleitung
2
3
Decor 240 2jet
31815XX3

Advertisement

loading
Need help?

Need help?

Do you have a question about the Decor 240 2jet 31815 3 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Hans Grohe Decor 240 2jet 31815 3 Series

  • Page 1 EN Instructions for use / assembly instructions DE Gebrauchsanleitung / Montageanleitung Decor 240 2jet 31815XX3...
  • Page 2: Safety Notes

    English The check valves must be checked regularly according Safety Notes to DIN EN 1717 in accordance with national or Gloves should be worn during installation to prevent regional regulations (at least once a year). crushing and cutting injuries. Operation (see page 8) The hot and cold supplies must be of equal • Hansgrohe recommends not to use as drinking water pressures. the first half liter of water drawn in the morning or Installation Instructions after a prolonged period of non-use. • Prior to installation, inspect the product for transport • Do not rotate the spout further than 360º or damage damages. After it has been installed, no transport or to the hose will result. surface damage will be honoured. • The pipes and the fixture must be installed, flushed and tested as per the applicable standards. • The plumbing codes applicable in the respective countries must be observed. Technical Data Operating pressure: max. 1 MPa Recommended operating pressure: 0,1 - 0,5 MPa Test pressure: 1,6 MPa (1 MPa = 10 bar = 147 PSI) Hot water temperature: max. 70°C Recommended hot water temp.: 65°C Thermal disinfection: max. 70°C / 4 min The product is exclusively designed for drinking water! Symbol description...
  • Page 3: Montage

    Deutsch Wartung (siehe Seite 11) Sicherheitshinweise Rückflussverhinderer müssen gemäß DIN EN 1717 Bei der Montage müssen zur Vermeidung von regelmäßig in Übereinstimmung mit nationalen oder Quetsch- und Schnittverletzungen Handschuhe regionalen Bestimmungen auf ihre Funktion geprüft getragen werden. werden (mindestens einmal jährlich). Große Druckunterschiede zwischen den Kalt- und Bedienung (siehe Seite 8) Warmwasseranschlüssen müssen ausgeglichen werden. • Hansgrohe empfiehlt, morgens oder nach längeren Montagehinweise Stagnationszeiten den ersten halben Liter nicht als Trinkwasser zu verwenden. • Vor der Montage muss das Produkt auf Transport- schäden untersucht werden. Nach dem Einbau • Auslauf nicht weiter drehen als 360º, da sonst der werden keine Transport- oder Oberflächenschäden Schlauch beschädigt werden kann. anerkannt. • Die Leitungen und die Armatur müssen nach den gültigen Normen montiert, gespült und geprüft werden. • Die in den Ländern jeweils gültigen Installationsricht- linien sind einzuhalten. Technische Daten Betriebsdruck: max. 1 MPa Empfohlener Betriebsdruck: 0,1 - 0,5 MPa Prüfdruck: 1,6 MPa (1 MPa = 10 bar = 147 PSI) Heißwassertemperatur: max. 70°C Empfohlene Heißwassertemperatur:...
  • Page 4 (3 Nm) CLICK SW 10 mm SW 24 mm (4 Nm)
  • Page 5 > 2 min (1 Nm)
  • Page 6 60 °C 10 °C 0,3 MPa 36°C 38°C 50°C 60°C 43°C 55°C 17 x...
  • Page 7 Ø Ø Ø 34 G 1/2 G 1/2...
  • Page 8 open / öffnen close / schließen hot / warm cold / kalt open / öffnen...
  • Page 10 Cleaning recommendation / Warranty / Contact einigungsempfehlung / Garantie / Kontakt www.hansgrohe.com/ cleaning-recommendation www.hansgrohe.com/ cleaning-recommendation www.hansgrohe.com/ cleaning-recommendation www.hansgrohe.com/ cleaning-recommendation...
  • Page 11 97735000...
  • Page 12 98193000 98356XX0 (32x2) 95562XX0 96338000 95498XX0 98127000 97209000 (11x2) (M37x1,5) 97735000 SW 30 mm 92730000 95332000 95332000 98231000 98422000 (18x1,5) 95140000 (7x1,5) (M4x20) 98459XX3 SW 4 mm 95008000 98140000 92482000 98212000 (20x1) (600 mm) (41x2) SW 24 mm 95910000 95909000 (M22x1) 97523000 95561000...