Precautions Before Installation; Before Installing; Installation Notes - Pioneer DMH-ZF9350BT Quick Start Manual

Installation
Precautions before
installation
CAUTION
• Never install this product in places where,
or in a manner that:
– Could injure the driver or passengers if
the vehicle stops suddenly.
– May interfere with the driver's operation
of the vehicle, such as on the floor in
front of the driver's seat, or close to the
steering wheel or gearstick.
• To ensure proper installation, be sure to
use the supplied parts in the manner
specified. If any parts are not supplied
with this product, use compatible parts in
the manner specified after you have the
part compatibility checked by your
dealer. If parts other than supplied or
compatible ones are used, they may
damage internal parts of this product or
they may work loose and the product
may become detached.
• It is extremely dangerous to allow cables
to become wound around the steering
column or gearstick. Be sure to install this
product, its cables, and wiring away in
such so that they will not obstruct or
hinder driving.
• Make sure that leads cannot get caught
in a door or the sliding mechanism of a
seat, resulting in a short circuit.
• Please confirm the proper function of
your vehicle's other equipment after
installation of this product.
• Do not install this product where it may
(i) obstruct the driver's vision,
(ii) impair the performance of any of the
vehicle's operating systems or safety
features, including airbags, hazard lamp
buttons or
(iii) impair the driver's ability to safely
operate the vehicle.
• Never install this product in front of or
next to the place in the dashboard, door,
or pillar from which one of your vehicle's
airbags would deploy. Please refer to your
vehicle's owner's manual for reference to
the deployment area of the frontal
airbags.

Before installing

• Consult with your nearest dealer if
installation requires drilling holes or
other modifications of the vehicle.
• Before making a final installation of this
product, temporarily connect the wiring
to confirm that the connections are
correct and the system works properly.

Installation notes

• Do not install this product in places
subject to high temperatures or
humidity, such as:
– Places close to a heater, vent or air
conditioner.
– Places exposed to direct sunlight, such
as on top of the dashboard.
– Places that may be exposed to rain,
such as close to the door or on the
vehicle's floor.
• Install this product horizontally on a
surface within 0 to 30 degrees tolerance
(within 5 degrees to the left or right).
Improper installation of the unit with the
surface tilted more than these tolerances
increases the potential for errors in the
vehicle's location display, and might
otherwise cause reduced display
performance.
• When installing, to ensure proper heat
dispersal when using this unit, make sure
you leave ample space behind the rear
panel and wrap any loose cables so they
are not blocking the vents.
5 cm
Leave ample
space
5 cm
• The cords must not cover up the area
shown in the figure below. This is
necessary to allow the amplifiers to
radiate freely. (DMH-ZS9350BT)
Do not cover this area
Installation using the screw
holes on the side of this
product
▶DMH-ZF9350BT
Installation tips
The following procedure describes how to
install this product with an LCD screen
attached to the unit. Depending on the
vehicle or installation location, you may
need to adjust the mounting position of
the LCD screen in order to prevent
impairment of vehicle driving operations.
For details on the mounting LCD screen
dimensions, refer to The adjusting position
and mounting dimension of the display
(page 17) before installing.
WARNING
Do not use a mounting sleeve to install this
unit to prevent it from popping out or
rattling.
1
Adjust the front-back position of the
front panel by removing the flush
surface screws on the front edge of the
unit ( ) then fix the face panel by
using the screw ( ) (optional).
Depending on the vehicle, the front-
back position of the front panel may
need to be adjusted to mount the LCD
screen. Slide the face panel to the front
before installing the unit to the vehicle.
Screw
En
13