Download  Print this page

Honeywell CT40-WS-PB Quick Start Manual

Arm mount sled and armband for dolphin ct40
Hide thumbs

Advertisement

Quick Links

-
Arm Mount Sled and Armband
Wearable Solution for Booted CT40
Models CT40-WS-PB, CT40-WS-AB, HWS-ARM BAND,
CT40-WS-00, CT40-WS-KIT
Quick Start Guide
CT40-WS-EN-QS-01 Rev A
1/20

Advertisement

Table of Contents
loading

  Related Manuals for Honeywell CT40-WS-PB

  Summary of Contents for Honeywell CT40-WS-PB

  • Page 1 Arm Mount Sled and Armband Wearable Solution for Booted CT40 Models CT40-WS-PB, CT40-WS-AB, HWS-ARM BAND, CT40-WS-00, CT40-WS-KIT Quick Start Guide CT40-WS-EN-QS-01 Rev A 1/20...
  • Page 2 Introduction The Honeywell Wearable Solution allows the user to mount a booted Dolphin CT40 mobile computer on either arm. It consists of an arm mount sled and an armband. The sled and armband can be purchased separately or together as a kit.
  • Page 3 Arm Mount Sled Features Ring Scanner Finger Ring Trigger I/O Connector Latch...
  • Page 4 Armband Features CT40-WS-AB Strap Clip Sled Release Clip Sled Release Clip Strap Horn Wrist Pad Arm Pad HWR-ARM BAND Strap Horn Sled Release Clip Sled Release Clip Strap Horn Arm Pad...
  • Page 5 Assemble the CT40 Wearable Solution The illustrations in this procedure assume the sled has not yet been mounted to the armband. However, the sled can be mounted to the armband before the user puts the armband on. Note: The sled requires the use of protective boot CT40-PB-00. Note: The wearable solution is not compatible with a hand strap.
  • Page 6 Place the armband on top of either arm. (Armband CT40-WS-AB shown for illustration purposes.) Buckle the straps around the arm and secure any excess strap length.
  • Page 7 Align the four tabs on the back of the sled with the notches on the armband and press down evenly until the assembly clicks together. HWR-ARM BAND...
  • Page 8 Rotate the ring scanner head to the desired orientation and insert finger. Note: The ring scanner cable should not cross under the hand. If the CT40 is awake, it will automatically connect to the ring scanner. If the CT40 is in sleep mode, tap the power button or the scan button on the CT40 to wake the device and connect to the scanner.
  • Page 9 Press the ring scanner trigger. The decode results display on the screen. Note: In the Scan Demo app, not all bar code symbologies are enabled by default. If a bar code does not scan, the correct symbology may not be enabled. To learn how to modify the default app settings, see the user guide.
  • Page 10 Remove the CT40 from the Wearable Solution Remove finger from the ring scanner. Press down on the clips on both sides of the armband to release the sled. (Armband CT40-WS-AB shown for illustration purposes.) Lift the sled out.
  • Page 11 Press down on the latch on the back of the sled to release the CT40. Lift the CT40 out of the sled. To remove the armband, loosen the straps to remove the assembly from the arm. It is not necessary to remove the straps from the buckles.
  • Page 12: Limited Warranty

    Patents For patent information, see www.hsmpats.com. Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.
  • Page 13 This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HII. Copyright © 2020 Honeywell International Inc. All rights reserved.

This manual is also suitable for:

Ct40-ws-abCt40-ws-00Ct40-ws-kitHws-arm band