1. Manuals
  2. Brands
  3. Iddero Manuals
  4. Intercom System
  5. HC2-KNX
  6. Configuration manual

Iddero HC2-KNX Configuration Manual

Touch panels
Hide thumbs Also See for HC2-KNX:
Table of Contents

Advertisement

Quick Links

IDDERO TOUCH PANELS
Video door phone configuration
www.iddero.com
120719-02

Advertisement

Table of Contents
loading

Related Manuals for Iddero HC2-KNX

Summary of Contents for Iddero HC2-KNX

  • Page 1 IDDERO TOUCH PANELS Video door phone configuration www.iddero.com 120719-02...

  • Page 2: Table Of Contents

    IDDERO TOUCH PANEL CONFIGURATION ................28 © 2011-2012 All Rights reserved. Iddero is a registered trademark of INGELABS, S.L. All other registered trademarks and trade names used in this document are the property of their respective owners. Other product and/or company names used in this document may be protected by copyrights, trademarks, or patents.

  • Page 3: Introduction

    INTRODUCTION The HC2-KNX 7” and HC2L-KNX 10,4” touch panels from Iddero can be used as indoor monitors for compatible video door phone systems. This document provides the necessary information to configure this functionality. INSTALLATION The HC2-KNX and HC2L-KNX touch panels support IP-based door phone systems. In order to interconnect the video door phone system and an Iddero touch panel, only a TCP/IP network connection is required.

  • Page 4: Initial Configuration

    INITIAL CONFIGURATION In order to use the video door phone function of the HC2-KNX / HC2L-KNX touch panel, you must first enable it in the Iddero configuration software. Before proceeding, please make sure you have selected “HC2-KNX” or “HC2L-KNX” in the “System type”...

  • Page 5: Helios Ip Video Door Phones

    All 2N Helios IP door communicators (Vario, Force, and Safety series) are supported. Two-way audio and the door opening function are implemented for all supported 2N Helios IP models. Visualization of video input in the HC2-KNX touch panel is supported for camera-equipped 2N Helios IP door communicators.
  • Page 6 Please make sure that the IP address assigned to the 2N Helios IP video door phone can be reached from the Iddero touch panel. For this, both devices must be in the same TCP/IP subnet. For example, if the touch panel’s IP address is 192.168.0.200, with subnet mask 255.255.255.0 (default values), assign an IP in the 192.168.0.x range to the video door phone (for example, 192.168.0.231), and set...
  • Page 7 For door phone stations not equipped with a professional license (2N Helios IP Basic): • Make sure JPEG video streaming is enabled (select “Anonymous access: Yes” in the JPEG video settings section) • Click on the save icon in the bottom right corner www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration...
  • Page 8 Ensure that this user is active (“User current state: Active”) • Enter the SIP address of the Iddero touch panel in the “Number 1” field of the “Phone numbers” section. The SIP address has the following syntax (replace <ip_address> with the actual IP address of the Iddero touch panel): sip:hc2@<ip_address>...
  • Page 9 Set “Switch mode” to “Monostable” Click on the save icon in the bottom right corner • If a second door exists in the building, repeat the above step in Basic Settings → Switch 2 www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration...
  • Page 10 Click on the save icon in the bottom right corner • If a second door exists in the building, you can also configure a door opening code for it in the Basic Settings → Switch 2 menu. www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration...

  • Page 11: Mobotix Video Door Phones

    This section provides enough information to configure Mobotix T24 video door phones for use in combination with the HC2-KNX touch panel. This information is provided for illustrative purposes only. For additional details, or for advanced configuration of the Mobotix T24 product, please refer to the documentation provided by Mobotix.
  • Page 12 Cameras… from the menu bar). A list of installed cameras will appear. Right-click on the camera associated with the T24 door station and select “Change network setup…” in the drop-down menu. www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration...
  • Page 13 Please make sure that the IP address assigned to the Mobotix video door phone can be reached from the Iddero touch panel. For this, both devices must be in the same TCP/IP subnet. For example, if the touch panel’s IP address is 192.168.0.200, with subnet mask 255.255.255.0 (default values), assign an IP in the 192.168.0.x range to the video door phone (for example, 192.168.0.231), and set the...
  • Page 14 “admin”, password: “meinsm”). Make a note of these values and click “Next”. MxEasy will now apply the new configuration to the door station’s camera. This will take a few seconds. Once this is done, click “Next” again to continue. www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration...
  • Page 15 You will now be asked to select the best display mode for the camera. The default display mode is “Panorama”. Change this to “Normal” mode (select “Normal” in the drop-down menu), and click “Next”. www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration...
  • Page 16 “Name” field (for example, “HC2”), and enter the IP address of the touch panel in the “Address” field. Click “OK” to close the dialog window, then “Next” to continue. MxEasy will now apply the new configuration. Once it is done, click “Finish”. www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration...
  • Page 17 “Proceed” to continue. After some moments a message will be shown indicating that the configuration completed successfully. Click “Ok”, then “Next” to move to the next step. www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration...
  • Page 18 Select the number of additional door bell modules (excluding the main one), and specify whether there are door position and lock position sensors connected. Once you are done, click “Next”. www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration...
  • Page 19 You can safely ignore the “PIN Code” field. Click “OK” to close the dialog window, then “Next” to continue. MxEasy will now apply the configuration. Once the process completes, press “Finish”. www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration...
  • Page 20 Locate the parameter “Action Details: Action Dead Time” and set its value to 0. Click on the “Set” button to apply the changes. • Finally, click on the “Close” button to save the new configuration in persistent memory. www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration...
  • Page 21 In the Image Control → General Image Settings section, select “Image Size: VGA (640x480) and “Display Mode: Normal”. Click “Set” to apply the changes. • Finally, click on the “Close” button to save the new configuration in persistent memory. www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration...

  • Page 22: Robin Telecom Video Door Phones

    This section provides enough information to configure Robin SmartView SIP video door phone systems for use in combination with Iddero touch panels. This information is provided for illustrative purposes only. For additional details, or for advanced configuration of the Robin SmartView SIP product, please refer to the documentation provided by the manufacturer.
  • Page 23 Please make sure that the IP address assigned to the Robin SmartView SIP video door phone can be reached from the Iddero touch panel. For this, both devices must be in the same TCP/IP subnet. For example, if the touch panel’s IP address is 192.168.0.200, with subnet mask 255.255.255.0 (default values), assign an IP in the 192.168.0.x range to the video door phone (for example, 192.168.0.231),...
  • Page 24 Enter a meaningful name in the “Description” field (for example, “HC2”) • Enter the SIP address of the Iddero touch panel in the “Number” field. The SIP address has the following syntax (replace <ip_address> with the actual IP address of the Iddero touch panel): hc2@<ip_address>...
  • Page 25 IDDERO TOUCH PANELS – Video door phone configuration...
  • Page 26 3. Door opening function configuration The Iddero configuration software allows you to select whether the door opening function operates over HTTP (recommended) or SIP. The first option (HTTP) allows opening the door from the touch panel even if there is no incoming call. With the second option (SIP), the door can only be opened once an incoming call has been accepted.
  • Page 27 • Audio → Mixer menu: “Speaker volume”: 100 “Microphone sensitivity”: 40 • Audio → Advanced menu: Verify that options “Echo canceler” and “Denoise” are enabled (checked) www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration...

  • Page 28: Iddero Touch Panel Configuration

    In the System Settings menu, press the “Video door phone” button to enter the video door phone settings section. Available options will depend on the video door phone type and configuration, as defined in the project. www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration...
  • Page 29 SIP and a second door has been enabled. Username: User name for video door phone access. Shown only if required. Password: Password for video door phone access. Shown only if required. www.iddero.com IDDERO TOUCH PANELS – Video door phone configuration...

This manual is also suitable for:

Hc2l-knx

Table of Contents