Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DCSENG S-CM4_M
Summary of Contents for DCSENG S-CM4_M
- Page 1 PIPE(TUBE) CUTTER Of Best Technology Manual ( CM4_M / CM4_OD) SAFETY PRECAUTIONS Thanks for choosing the S-Cutter. Make sure that you carefully read and fully understand the Manual to use the device correctly and keep yourself and your properties safe.
-
Page 2: Table Of Contents
PIPE(TUBE) CUTTER Of Best Technology CONTENTS 1. SAFETY PRECAUTIONS 2. Must-Follow Rules 3. Instruction Before Use 4. How to Use ● S-CM4_M ● S-CM4_OD 5. Quality Warranty... -
Page 3: Safety Precautions
SAFETY PRECAUTIONS Keep workplace clean and well-lit at all times. An untidy or dark workplace may cause accidents. Consider your work environment. Do not let it wet. Do not use in humid place. Install bright lighting in the work place. Do not use the machine near the flammable liquids or gases. - Page 4 PIPE(TUBE) CUTTER Of Best Technology Do NOT abuse the cord. Do not drag the product by pulling the electric cord. Do not unplug the cable by pulling the cord itself. Keep the cord safe from heat, oil and sharp edges. Install the anti-scattering protector of cutting chips.
- Page 5 Be cautious all the time. Observe work process and process accordingly. Do not use this product if the concentration is blurred, Do not operate by force the cutting speed and rotational speed. Make sure that there is no damage on the product. Check the safety device and examine thoroughly that the mildly damaged parts now function normally before resuming the use of the tool.
-
Page 6: Must-Follow Rules
PIPE(TUBE) CUTTER Of Best Technology Must-Follow Rules The instructions in this user manual contains information that is important to the safe use of this product. Not following these instructions can cause death, serious injury, and massive property damage. For safety, the instructions are divided into ‘WARNING’ and ‘CAUTION’ depending on degree of risk, and the details are as follows: Symbol Description... - Page 7 Warning ● Do not pour water or cutting fluid. Due to water or other liquids on the electric motor, electric shock, or death may occur. ● Do not use tools in wet conditions or rain. Serious injury or death may occur by electric shock. ●...
-
Page 8: Instruction Before Use
PIPE(TUBE) CUTTER Of Best Technology Instruction before use Check the electric leakage breaker Make sure the system is powered on the circuit breaker is installed. Check if an electric leakage breaker (ELB) with rated capacity is installed in all electric units. Make sure that the ground wire is connected to the powered system. -
Page 9: S-Cm4_M
CM4_M Portable hand bevel and coating removal Bevel capacity : 0-90°, 0-14C Pipe/plate : coating removal(zinc coating) and bevel processing S-Cutter... - Page 10 02. Accessories 03. How to adjust the bevel angle 04. How to adjust the guide roll 05. How to adjust the processing depth 06. How to change the insert tip 07. How to use the S-CM4_M 08. Product specifications www.s-cutter.co.kr...
-
Page 11: Name And Function Of The Parts
1. Name and function of the parts Name Function Guide Processing guide Guide groove Selecting the optimal area when processing Guide roll Providing the convenience of work Roll fixing lever Fixing the guide roll Goniometer Bevel angle adjustment marking Angle adjusting bolt Guide plate fixing bolt Rubber sheet Prevention of flame and chip scattering... -
Page 12: Accessories
PIPE(TUBE) CUTTER Of Best Technology 2. Accessories Hexagon wrench Star wrench Tip box Auxiliary handle Insert Tip ● Standard accessories Star wrench : For changing the insert tip(T15). Hexagon wrench : For tightening the angle adjusting bolt(5mm). Auxiliary handle : Installed to the side of equipment when using with both hands. ●... -
Page 13: How To Adjust The Bevel Angle
3. How to adjust the bevel angle Loosen all 4 angle adjusting bolts by using hexagon wrench. 3-1. Angle adjusting bolt Hexagon wrench After loosening angle adjusting bolts(4ea), set the guide into the 3-2. desired angle by looking at the goniometer, and then tighten the angle adjusting bolts(4ea). -
Page 14: How To Adjust The Guide Roll
PIPE(TUBE) CUTTER Of Best Technology 4. How to adjust the guide roll Put the guide groove to the top of pipe at first, place on the external 4-1. surface of pipe by loosening the roll fixing lever as shown in the picture, and tighten the roll fixing lever firmly(refer to Ref.7 for detailed processing method). -
Page 15: How To Adjust The Processing Depth
5. How to adjust the processing depth Insert tip is ascended or descended by rotating the adjusting wheel as shown in the picture(refer to Ref.7 for detailed processing method). CCW rotation CW rotation Adjustable handle Cutting depth Down Down Down Down Down Ref.1) -
Page 16: How To Change The Insert Tip
PIPE(TUBE) CUTTER Of Best Technology 6. How to change the insert tip As shown in the picture, insert tip can be changed by loosening the 6-1. bolt of insert tip with star wrench provided as a standard component. ※ Reference) It is easier to work after descending the equipment by rotating the adjusting wheel clockwise on full lock. - Page 17 7. How to use S-CM4_M 7-1. Work order Checking the tip ➜ checking the angle(width) ➜ returning to tool ➜ adjusting the guide ➜ adjusting the tool by operating the equipment while it is on the pipe ➜ working after checking the final processing value ➜ continuing(repeating) the work 1) Checking the tip Check whether all 4 insert tips are installed well.
- Page 18 PIPE(TUBE) CUTTER Of Best Technology 5) Adjusting the tool by operating the equipment while it is on the pipe - Switch for the operation of equipment should not be adjusted while attaching the pipe, but adjust the switch while holding it in hand. - After the placement of equipment on pipe, check whether insert tip is attaching the surface of pipe by rotating the adjusting wheel gradually.
- Page 19 [Surface processing] - In case of surface processing, attach the guide groove to the pipe, and maintain the horizontality by attaching the front guide roll or back guide roll to the pipe in accordance with the direction of force(equal work is available when guide groove is attaching to the top of pipe).
- Page 20 PIPE(TUBE) CUTTER Of Best Technology 7-4. Checking the adherence of rubber sheet - Rubber sheet adheres on the side of equipment as shown in the picture below, and it blocks the chip or flame scattering while using the equipment. - Please check whether the rubber sheet is installed before starting the work, and purchase the rubber sheet again by calling the head office or local branch if it is damaged.
-
Page 21: Cm4_Od
8. Product specifications ● S-CM4_M cannot adjust the width during surface(flat) processing of pipe/plate, and 26mm of width is fixed as shown in the machine specification processing capacity below {90°(surface)}. Please use S-CM4_OD if width adjustment is needed. ● Please refer to the machine specification table or contact the head office for the details about the processing capacity. -
Page 22: S-Cm4_Od
PIPE(TUBE) CUTTER Of Best Technology CM4_OD Pipe/plate coating removal machine Processing capacity : 48mm of maximum width, 15mm of maximum depth Pipe/plate : coating(zinc coating) removal and flat processing www.s-cutter.co.kr... - Page 23 How to Use S-CM4_OD How to Use S-CM4_OD Instructions Before Use Please read about how to use manual provided by the headquarter or suppliers. Users must be educated before use. Make sure to remove the power when changing the insert tip. Be sure to use consumables(such as insert tip) for this equipment that are provided by us.
- Page 24 PIPE(TUBE) CUTTER Of Best Technology 1. Name and function of the parts Name Function Guide Processing guide Guide roll Selecting the optimal area when processing Roll fixing lever Fixing the guide roll Processing width Flat processing reference marking adjustment marking Processing width Guide plate fixing bolt adjustment bolt...
- Page 25 2. Standard parts Same as S-CM4_M (refer to explanation of No.2) 3. How to adjust the processing width Loosen all 4 processing width adjustment bolts by using T-hex wrench. 3-1. Processing width adjusting bolt Hexagon wrench Move the guide into the desired width by looking at the processing 3-2.
- Page 26 PIPE(TUBE) CUTTER Of Best Technology 4. How to adjust the guide roll Same as S-CM4_M (refer to explanation of No.4) 5. How to adjust the processing depth Same as S-CM4_M (refer to explanation of No.5) 6. How to change the insert tip Same as S-CM4_M (refer to explanation of No.6)
-
Page 27: Product Specifications
8. Product specifications ● During the flat processing of plate and pipe with S-CM4_OD, it does not match with processing width marking certainly. In other words, maximum processing width is smaller for the pipes with smaller diameter compared to the pipes with larger diameter even after the processing with the same processing depth since the contacting section of insert tip is different in accordance with the diameter of pipe. - Page 28 PIPE(TUBE) CUTTER Of Best Technology 9. Maintenance and inspection Be fully aware of the cautions for the safe usage. When maintaining or inspecting, please remove the power plug Inspection of the screw device for each part. Regularly check that the device on each part where the screw is loosened.
- Page 29 Action to take when tip bolt is damaged 9-1. If the tip bolt is damaged due to the carelessness, overload, accumulation of fatigue, etc. as shown in the picture below, it is easily removed through the counterclockwise rotation toward the edge of damaged tip bolt by using a sharp material, such as a gimlet, knife, etc., instead of hitting with a hammer or welding.
- Page 30 □ S-CM4_M □ S-CM4_OD...
- Page 31 PIPE(TUBE) CUTTER Of Best Technology DCSENG CO., LTD. 23-22, Jukjeon-3gil, Hyeondo-myeon, Seowon-gu, Cheongju-si, Chungcheongbuk-do, 28214, Republic of Korea T +82-43-256-0945 F +82-43-256-0946 W www.dcseng.co.kr www.s-cutter.co.kr...
Need help?
Do you have a question about the S-CM4_M and is the answer not in the manual?
Questions and answers