Yamaha YC Series Owner's Manual page 63

Doesn't reset the following data:
PROGRAM CHANGE, BANK SELECT MSB/LSB, VOLUME
(3-2-3) ALL NOTE OFF (CONTROL NUMBER = 7BH, DATA VALUE = 0)
All the notes currently set to on in certain channel(s) are muted when receiving this
message. However, if Sustain or Sostenuto is on, notes will continue sounding until
these are turned off.
(3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH, DATA VALUE = 0)
Performs the same function as when receiving ALL NOTES OFF.
(3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH, DATA VALUE = 0)
Performs the same function as when receiving ALL NOTES OFF.
(3-3) SYSTEM REAL TIME MESSAGES
(3-3-1) ACTIVE SENSING
STATUS 11111110(FEH)
Transmitted every 200 msec.
Once this code is received, the instrument starts sensing. When neither status
messages nor data are received for more than approximately 350 ms, the MIDI
receive buffer will be cleared, and the sounds currently being played are forcibly
turned off.
(3-4) SYSTEM EXCLUSIVE MESSAGE
(3-4-1) UNIVERSAL NON REALTIME MESSAGE
(3-4-1-1) IDENTITY REQUEST (Receive only)
F0H 7EH 0nH 06H 01H F7H ("n" = Device No. However, this
instrument receives under "omni.")
(3-4-1-2) IDENTITY REPLY (Transmit only)
F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH mmH 00H 00H 7FH
F7H
dd: Device family number/code
YC61: 5CH 06H
mm: version
mm=(version no.-1.0)*10
e.g.) version 1.0 mm=(1.0-1.0)*10=0
version 1.5 mm=(1.5-1.0)*10=5
(3-4-2) UNIVERSAL REALTIME MESSAGE
(3-4-3)PARAMETER CHANGE
(3-4-3-1) NATIVE PARAMETER CHANGE, MODE CHANGE
11110000 F0
01000011 43
0001nnnn 1n
01111111 7F
00011100 1C
00001001 09
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0ddddddd ddddddd
| |
11110111 F7
For parameters with data size of 2 or more, the appropriate number of data
bytes will be transmitted.
See the following MIDI Data Table for Address.
(3-4-4) BULK DUMP
11110000 F0
01000011 43
0000nnnn 0n
01111111 7F
00011100 1C
0bbbbbbb bbbbbbb
0bbbbbbb bbbbbbb
00001001 09
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0 0
| |
0ccccccc ccccccc
11110111 F7
See the following MIDI Data Table for Address and Byte Count.
Checksum is the value that results in a value of 0 for the lower 7 bits when
the Byte Count, Start Address, Data and Checksum itself are added.
(3-4-5) DUMP REQUEST
11110000 F0
01000011 43
0010nnnn 2n
01111111 7F
00011100 1C
00001001 09
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
11110111 F7
See the following MIDI Data Table for Address.
Exclusive status
YAMAHA ID
Device Number
Group ID High
Group ID Low
Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
Exclusive status
YAMAHA ID
Device Number
Group ID High
Group ID Low
Byte Count
Byte Count
Model ID
Address High
Address Mid
Address Low
Data
Check-sum
End of Exclusive
Exclusive status
YAMAHA ID
Device Number
Group ID High
Group ID Low
Model ID
Address High
Address Mid
Address Low
End of Exclusive
(3-4-6) PARAMETER REQUEST
11110000 F0
01000011 43
0011nnnn 3n
01111111 7F
00011100 1C
00001001 09
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
11110111 F7
See the following MIDI Data Table for Address.
(4) SYSTEM OVERVIEW (Keyboard and Tone Generator)
Zone Mode SW
Keyboard
Zone Settings
Local Control
MIDI Port
MIDI SW
MIDI IN
USB Port 1
MIDI Port
USB SW
USB Port 2
USB Port 2 is enabled when 'MIDI Port MIDI SW = OFF'
and 'MIDI Port USB SW = ON'
ALL SOUND OFF clears all the sounds in the specific channel(s) played by both the keyboard
and the data via MIDI.
ALL NOTES OFF received via MIDI clears the sounds in the specific channel(s) played via
MIDI.
DATA LIST
Exclusive status
YAMAHA ID
Device Number
Group ID High
Group ID Low
Model ID
Address High
Address Mid
Address Low
End of Exclusive
MIDI Port
MIDI SW
MIDI Out
MIDI Port
USB SW
USB Port 1
Organ
External Keyboard SW
Organ
Upper
Section
Organ
Lower
Section
Keyboard A
External Keyboard SW
Keyboard A
Section
Keyboard B
External Keyboard SW
Keyboard B
Section
USB Port 2
YC61 Owner's Manual
63