Autonics APC-1011 User Manual
  1. Manuals
  2. Brands
  3. Autonics Manuals
  4. Touch Panel
  5. APC-1011
  6. User manual
Autonics APC-1011 User Manual

Autonics APC-1011 User Manual

Hide thumbs Also See for APC-1011:
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual
Panel PC
APC-1011
Thank you for purchasing an Autonics product.
This user manual contains information about the product and its proper use,
and should be kept in a place where it will be easy to access.
www.autonics.com
.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the APC-1011 and is the answer not in the manual?

Questions and answers

Related Manuals for Autonics APC-1011

Summary of Contents for Autonics APC-1011

  • Page 1 User Manual Panel PC APC-1011 Thank you for purchasing an Autonics product. This user manual contains information about the product and its proper use, and should be kept in a place where it will be easy to access. www.autonics.com...
  • Page 2 © Copyright Reserved Autonics Co., Ltd.

  • Page 3: Preface

    Preface Preface Thank you for purchaseing Autonics product. Please familiarize yourself with the informaton contained in the Safety Precautions section before using this product. This user manual contains information about the product and its proper use, and should be kept in a place where it will be easy to access.

  • Page 4: User Manual Guide

    Visit our website (www.autonics.com) to download a copy.  The manual’s content may vary depending on changes to the product’s software and other unforeseen developments within Autonics, and is subject to change without prior notice. Upgrade notice is provided throughout the website. ...

  • Page 5: User Manual Symbols

    Failure to follow instructions can result in serious injury or death. Failure to follow instructions can lead to a minor injury or product damage. An example of the concerned feature’s use. ※1 Annotation mark. © Copyright Reserved Autonics Co., Ltd.

  • Page 6: Safety Considerations

    Since Lithium battery is embedded in the product, do not disassemble or burn the unit. Failure to follow this instruction may result in fire.  Do not disassemble or modify the unit. Failure to follow this instruction may result in fire.  Please contact us for battery replacement. © Copyright Reserved Autonics Co., Ltd.
  • Page 7 Failure to follow this instruction may result in malfunction. The specifications are subject to change and some models may be discontinued without notice. Be sure to follow cautions written in the instruction manual, user manual and the technical descriptions (catalog, website). © Copyright Reserved Autonics Co., Ltd.

  • Page 8: Cautions During Use

    If it gets into the eyes, rinse eyes with running water for over 15 minutes and contact a doctor.  This unit may be used in the following environments. ①Indoors (in the environment condition rated in 'Specifications') ②Altitude max. 2,000m ③Pollution degree 2 ④Installation category II viii © Copyright Reserved Autonics Co., Ltd.

  • Page 9: Table Of Contents

    Logic Panel Programing Program [SmartStudio] ........30 Software Installation ....................30 Operating Panel PC .................. 31 Power Supplying Checklist ..................31 Operation Procedure ....................31 Settings ...................... 33 Touchside Settings ....................33 5.1.1 Touch Settings .................... 34 © Copyright Reserved Autonics Co., Ltd.

  • Page 10: Table Of Contents

    Table of Contents 5.1.2 Draw Test ....................35 Windows Settings ....................35 Maintenance ....................37 Routine Maintenance ....................37 Regular Maintenance ....................37 © Copyright Reserved Autonics Co., Ltd.

  • Page 11: Product Overview

    1 Product Overview Product Overview Features Panel PC APC-1011 is a Microsoft Windows 10 based HMI(Human-Machine Interface) or MMI(Man-Machine Interface) device. As a display panel and a system unit integrated panel PC, the installation restrictions are less, User who is familiar with Windows 10 is able to use easily without any education.

  • Page 12: Specifications

    ※1: Supported language can be added by downloading language pack. For more details about language pack, please visit Microsoftwebsite. ※2: The weight includes packaging. The weight in parenthesis is for unit only. ※Environment resistance is rated at no freezing or condesation. © Copyright Reserved Autonics Co., Ltd.

  • Page 13: Performance Specifications

    Within 85° of top/bottom/left/right Backlight White LED Backlight MTBF 500,000 hrs (LED Backlighting) Luminance 350cd/m2 Interface type HDMI USB 3.0 HOST: 1, USB 2.0 HOST: 2 Ethernet Gigabit Ethernet: 2 Audio Serial RS232C/RS422/RS485: 1 (jumper pin setting) © Copyright Reserved Autonics Co., Ltd.

  • Page 14: Dimensions

    1 Product Overview Dimensions 1.3.1 Main Device (unit: mm) © Copyright Reserved Autonics Co., Ltd.

  • Page 15: Bracket

    1 Product Overview 1.3.2 Bracket (1) Fixing bracket (2) Mold bracket 1.3.3 Panel Cut-out ※Panel thickness: Max. 4mm © Copyright Reserved Autonics Co., Ltd.

  • Page 16: Unit Description

    ④ ⑤ USB 2.0 ⑥ Ethernet ⑦ USB 3.0 ⑧ Audio ⑨ RS232C/RS485/RS422(jumper pin setting) ⑩ Power switch ⑪ Power terminal ⑫ Fixing bracket mounting slot ⑬ Mold bracket mounting hole ⑭ VESA hole © Copyright Reserved Autonics Co., Ltd.

  • Page 17: Communication Interface

    1.5.1 Serial Interface (1) Changing serial interface 1st Open the rear case of APC-1011 with a screw driver. 2nd Set the serial interface selecting jumper pin(①) with the jumper bar to serial interface to use. 3rd When setting to RS232, connect the D-sub connector to COM2(②).

  • Page 18: Usb 2.0 Interface

    1 Product Overview 1.5.2 USB 2.0 Interface USB HOST 1.5.3 USB 3.0 Interface USB HOST SSRX1- SSRX1+ SSTX1- SSTX1+ © Copyright Reserved Autonics Co., Ltd.

  • Page 19: Ethernet Interface

    In case of connecting with ethernet router, use direct cable.  Straight(Direct) through – Cable Cable color Signal Pin no. Pin no. Signal White Orange Orange White Green Blue White Blue Green White Brown Brown Tx: Transmit Data, Rx: Receive Data © Copyright Reserved Autonics Co., Ltd.
  • Page 20 1 Product Overview © Copyright Reserved Autonics Co., Ltd.

  • Page 21: Installation

    If you use bolt out of specification, it my result in product damage. (2) Installing with holder You have to purchase 100×100mm holder separately. Autonics does not have dedicated holder. Fix the purchased holder to the VESA hole on the rear of the product, using M4 Screw driver.

  • Page 22: Power Wiring

    When connecting power, supply power with the power supply which has inner protection circuit. If the power supply which does not have inner protection circuit is used, protection circuits such as fuse must be installed before using this. © Copyright Reserved Autonics Co., Ltd.

  • Page 23: Ground Wiring

    Caution for ground wiring  Connect max. 100Ω of ground resistance.  Diameter of cable for ground wiring connection should be over than 2 ㎟.  As above figure, separate from other device’s ground wire. © Copyright Reserved Autonics Co., Ltd.
  • Page 24 2 Installation © Copyright Reserved Autonics Co., Ltd.

  • Page 25: Software

    Software list 3.1.1 Comprehensive Device Management Program [DAQMaster] DAQMaster is a comprehensive device management program that can be used with Autonics communication supporting products. DAQMaster provides GUI control for easy and convenient management of parameters and multiple device data monitoring.

  • Page 26: Comprehensive Motion Device Management Program [Atmotion]

    Autinics motion controller (AiC-D, PMC-2HSP/2HSN, PMC-1HS/2HS, PMC-4B-PCI). atMotion provides GUI control for easy and convenient parameter setting and monitoring data management of multiple devices. © Copyright Reserved Autonics Co., Ltd.

  • Page 27: Vision Sensor Program [Vision Master]

    3 Software 3.1.3 Vision Sensor Program [Vision Master] Vision Master is the vision sensor program that is connected with VG Series, Autonics vision sensor, to utilize it. Vision Master provides graphic user interface to make setting parameter and managing monitoring data of vision sensor easy.

  • Page 28: Comprehensive Laser Scanner Management Program [Atlidar]

    LSE-4A5R2. atLidar is the management program for laser scanner installation, parameter settings, status information and monitoring data, etc. This program communicates with the laser scanner via Ethernet communication. © Copyright Reserved Autonics Co., Ltd.

  • Page 29: Drawing Program For Gp/Lp Panel [Gp Editor]

    All data of GP/LP user screen is edited in exclusive software GP Editor. After editing screen data including forms, layout, properties of tags and etc., download data to GP/LP, it starts to monitor by the screen data of GP/LP. © Copyright Reserved Autonics Co., Ltd.

  • Page 30: Logic Panel Programing Program [Smartstudio]

    3rd Touch the installation file in APC-1011 to install the program. (2) Direct installation 1st Plug LAN cable to Ethernet port of APC-1011 to connect to Internet. 2nd Access to Autonics website (www.autonics.com) in APC-1011 to download program. 3rd Touch the downloaded installation file in APC-1011 to install the program.

  • Page 31: Operating Panel Pc

    4 Operating Panel PC Operating Panel PC Describes the operation procedure from when the power is supplied on APC-1011 to when the software is executed. Power Supplying Checklist Please check the following list below, before supplying the power on APC-1011.
  • Page 32 4 Operating Panel PC © Copyright Reserved Autonics Co., Ltd.

  • Page 33: Settings

    Run the draw test to check the calibration status. Display Check the current display status. Display Operation Mode Set the touch functioning area on the screen. Other Other Set the touch functioning area on the screen in detail. © Copyright Reserved Autonics Co., Ltd.

  • Page 34: Touch Settings

    2nd Set the ‘Linearization Style’ on ‘Setting’ tap. 3rd Click the ‘Linearization’ on ‘Tools’ tap. When the caliblation screen shows up, touch and hold the 9 touch points in sequence untill OK appears to correct the touch points. © Copyright Reserved Autonics Co., Ltd.

  • Page 35: Draw Test

    Click ‘Clear’ to erase all drawn lines, and click ‘Quit’ to exit the drawing test. Windows Settings Please refer to Microsoft for corresponding contents such as changing system languange, system setting, account management and etc. © Copyright Reserved Autonics Co., Ltd.
  • Page 36 5 Settings © Copyright Reserved Autonics Co., Ltd.

  • Page 37: Maintenance

    When the defect is found, please record and notify us the defect in detail.  When replacing the product, make sure to turn the power off.  When removing dust or dirt, use a dry cloth that does not contain water or detergent. © Copyright Reserved Autonics Co., Ltd.
  • Page 38 * Dimensions or specifications on this manual are subject to change and some models may be discontinued without notice. MTO-APC1011U1-V1.1-1905US...

Table of Contents