Sony DVP-NC650V Service Manual page 14

B Connecting to an AV amplifier (having 5.1ch input jacks or a digital input
jack) and 4 to 6 speakers
If your AV amplifier (receiver) has 5.1 channel inputs, use
If you want to use the Dolby Digital or DTS decoder function on your AV amplifier (receiver),
connect to its digital jack using . With the following connections, you can enjoy a more
B-2
realistic audio presence in the comfort of your own home.
: Connecting to the 5.1ch input jacks
B-1
You can enjoy 5.1ch surround sound using the internal Dolby Digital, DTS or SACD Multi
decoder of this player. You can also enjoy Dolby Surround (Pro Logic) sounds, or surround
sounds using various "SURROUND" modes (page 58).
xRecommended surround sound effects for this connection
When 6 speakers are connected (Set "SURROUND" to "OFF.")
• Dolby Digital (5.1ch) (page 92)
• DTS (5.1ch) (page 92)
• SACD Multi-channel (page 93)
: Connecting to a digital jack
B-2
This connection will allow you to use the Dolby Digital or DTS decoder function of your AV
amplifier (receiver). You are not able to enjoy the surround sound effects of the player.
xRecommended surround sound effects using this connection with your amplifier (receiver)
• Dolby Digital (5.1ch) (page 92)
• DTS (5.1ch) (page 92)
• 96 kHz/24 bit PCM
z
Refer to the operating instructions of the AV amplifier (receiver) for correct speaker setting location when using
B-2
the connection.
Notes
• After you have completed the connection, be sure to set "DOLBY DIGITAL" to "DOLBY DIGITAL" (page 84)
and "DTS" to "DTS" (page 85). Otherwise, no sound or a loud noise will come from the speakers.
• When you connect an amplifier (receiver) that conforms to the 96 kHz sampling frequency, set "48kHz/96kHz
PCM" to "96kHz/24bit" (page 85).
• SACD audio signals are not output from a digital jack.
22
C
Connecting to a stereo amplifier (receiver) and 2 speakers/Connecting to an
MD deck or DAT deck
This connection will use your 2 front speakers connected to your stereo amplifier (receiver) for
sound. If the stereo amplifier (receiver) has audio input jacks L and R only, use
amplifier (receiver) has a digital input jack, use
deck, use C-2 . In this case, you can also connect the player directly to the MD deck or DAT
deck without using your stereo amplifier (receiver).
xRecommended surround sound effects for the
• TVS STANDARD (page 58)
z
In connection , you can use the supplied audio/video cord instead of using a separate audio cord.
C-1
z
To realize better surround sound effects, make sure that your listening position is in between your speakers.
Note
SACD audio signals are not output from a digital jack.
24
B-1 .
C-1
. If the
C-2
. When connecting to an MD deck or a DAT
C-1 connection only
SACD/DVD player
Optical digital cord
(not supplied)
Remove jack cap
before connecting.
or
Coaxial digital cord
(not supplied)
to coaxial or optical
digital input
[Speakers]
AV amplifier (receiver) having
5.1ch inputs or/and a decoder
Subwoofer
Center
l: Signal flow
z
To enhance the surround sound effects:
• Use high-performance speakers.
• Use front, rear, and center speakers having the same size and performance.
• Place a subwoofer between the right and left front speakers.
•
SACD/DVD player
Coaxial digital cord
(not supplied)
or
Optical digital cord
(not supplied)
Remove the jack
cap before
connecting.
to coaxial or optical
digital input
[Speakers]
Stereo amplifier (receiver)
Front (L)
Front (R)
l: Signal flow
1-5
Stereo audio cord
(not supplied)
or
Monaural audio cord
(not supplied)
to audio input
[Speakers]
Front (L)
Front (R)
Rear (L)
continued
Stereo audio cord
(not supplied) (red)
(white)
or
(red)
(white)
to audio input
MD deck/DAT deck
continued
Rear (R)


23


25