Advertisement
ESCORT II AND III JUICE DISPENSERS
ELECTRONIC ICE BANK CONTROL (EIBC)
1. REMOVAL AND INSTALLATION INSTRUCTIONS
DISCONNECT FROM POWER SOURCE BEFORE BEGINNING THIS PROCEDURE. WATER BATH
MUST BE DRAINED AND ICE BANK MUST BE COMPLETELY MELTED. DO NOT ATTEMPT TO
CHANGE PROBE WITH ICE BANK STILL FROZEN.
1.1
Remove two (2) screws retaining Rear Lid over Agitator Deck and remove Lid.
1.2
Disconnect leads from load side of Transformer and disconnect Agitator/IBC connector at top inside
corner of dispenser.
1.3
Remove two (2) screws retaining Agitator Deck and remove Agitator Deck. Take care not to
damage Agitator propeller during retrofit.
1.4
Remove cover from Ranco IBC.
1.5
Remove three (3) leads from Ranco Control, noting which lead goes to the Junction Box and which
lead goes to the Compressor (third lead goes to Agitator Motor). The lead going to the Compressor
is on Pin 1 of the Agitator/IBC connector and the lead going to the Junction Box is on Pin 3 (see
Figure 1A).
1.6
Remove the hole plug insulation around the Ranco probe capillary tube and remove the Ranco
Probe and Ranco Control Box from the Agitator Deck.
reinstallation.
• NORTH AMERICA – 210-310-7245 • INTERNATIONAL SALES – 210-310-7242 • CUSTOMER SERVICE – 210-310-7242 •
• LATIN AMERICA – 210-524-9567 / 210-310-7245 • EUROPE – 32-2-755-2399 • PACIFIC – 61-8-8268-1978 •
"Lancer" is the registered trademark of Lancer • Copyright — 2001 by Lancer, all rights reserved.
INSTALLATION INSTRUCTIONS
RETROFIT KIT (PN 82-3049)
WARNING
Figure 1A
6655 LANCER BLVD. • SAN ANTONIO, TEXAS 78219 USA • (210) 310-7000
FAX SALES
FAX ENGINEERING: • 210-310-7096
Save screws and insulation plug for
DATE: 08/10/01
P.N.:
28-0502
Advertisement
Table of Contents
Related Manuals for lancer 82-3049
Summary of Contents for lancer 82-3049
- Page 1 • LATIN AMERICA – 210-524-9567 / 210-310-7245 • EUROPE – 32-2-755-2399 • PACIFIC – 61-8-8268-1978 • DATE: 08/10/01 FAX ENGINEERING: • 210-310-7096 "Lancer" is the registered trademark of Lancer • Copyright — 2001 by Lancer, all rights reserved. P.N.: 28-0502...
- Page 2 Figure 1B Remove one (1) screw holding the bracket on the Lancer Electronic Ice Bank Control housing (EIBC) and loosen the other. Spin the bracket 90° as shown in Figure 2, reinstall screw and tighten both screws. Mount EIBC Control Housing Assembly at holes previously used for the Ranco Control, using the screws removed in Step 1.6.
- Page 3 Figure 3 1.10 Turn Agitator Deck Assembly over. Using a hack saw or similar tool, cut off the tube that once held the Ranco probe as close to the tube retaining ring as possible. Deburr the cut edge. 1.11 Attach EIBC Probe to Clamp Assembly (as shown in Figure 3) using supplied 6-32 x 1/2 screws. Do not overtighten this assembly.
- Page 4 1.19 Replace Rear Lid over Agitator Deck and the two screws. 1.20 Conduct operational check of unit. Please refer to the Lancer web site (www.lancercorp.com) for information relating to Lancer Installation and Service Manuals, Instruction Sheets, Technical Bulletins, Service Bulletins, etc.
Need help?
Do you have a question about the 82-3049 and is the answer not in the manual?
Questions and answers