Related Manuals for Ketra X2
Summary of Contents for Ketra X2
- Page 1 K E Y PA D Installation Guide Model X2-ND - KetraNet Mesh Keypad 120-277 V~ X2-INC - KetraNet Mesh + 600 W Incandescent Dimmer 120 V~...
- Page 2 Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: • This device may not cause interference. • This device must accept any interference, including interference that may cause undesired operation of the device. 770-000026-01 r12 2 | X2 INSTALLATION GUIDE © 2019 Ketra, Inc. All rights reserved...
-
Page 3: Table Of Contents
Dimmer Load Wiring Diagrams Installation X2-ND AC Input, Non-dimming Retrofit Important Notes Retrofit Instructions X2-INC Incandescent Dimmer Retrofit Important Notes Replacing Button Chassis Operation Warranty & Tech Support 770-000026-01 r12 3 | X2 INSTALLATION GUIDE © 2019 Ketra, Inc. All rights reserved... -
Page 4: Product Overview
Mesh controller with onboard incandescent dimmer. The latter is ideal for spaces where both Ketra and traditional lighting sources need to be controlled. Fitting within a standard wall box and either Decora® or Claro wall plates, the X2 is perfect for retrofit installations as well as new construction. -
Page 5: Included Components/Specs
Input Wiring Location UL Damp Location, IP20 Voltage X2.ND 120-277 VA X2.INC 120 V Mechanical Power Consumption Weight 8.8 oz/250 kg 50/60 Hz Frequency Housing Material Flame Retardant Polymer 770-000026-01 r12 5 | X2 INSTALLATION GUIDE © 2019 Ketra, Inc. All rights reserved... -
Page 6: Dimension Drawings
(105 mm) (83.6 mm) (66.23 mm) 1.4 in 0.3 in (7.6 mm) (35.3 mm) 1.7 in (43.97 mm) multi-gang trim 0.2 in (6.1 mm) 2.4 in (60.15 mm) 770-000026-01 r12 6 | X2 INSTALLATION GUIDE © 2019 Ketra, Inc. All rights reserved... -
Page 7: Dimmer Load
Dimmer Load X2-INC Load Type and Capacity Chart Load Type Single Gang Multigang Incandescent 600 W 500 W Dimmer capacity rated at 25 ˚C ambient temperature; derate incandescent and halogen loads an additional 100 W at 40 ˚C temperature ambient. -
Page 8: Wiring Diagrams
LOAD Black Hot/Line Black White White Green Neutral X2 INC X2 ND Ground Green Traveler 2 (not used) X2 Keypad, X2 Keypad, AC INC dimmer input, no dimmer 770-000026-01 r12 8 | X2 INSTALLATION GUIDE © 2019 Ketra, Inc. All rights reserved... - Page 9 Hot/Line Neutral Ground LOAD Black Black White White X2 INC X2 ND Green Traveler 2 Green (not used) X2 Keypad, X2 Keypad, AC INC dimmer input, no dimmer 770-000026-01 r12 9 | X2 INSTALLATION GUIDE © 2019 Ketra, Inc. All rights reserved...
-
Page 10: Installation
Prepare the wire for connection to lead wire: A. Strip 8.5 mm of wire for insertion into the wire nut. B. Twist the stranded wire to prevent fraying (tinning optional). Using the provided wire nuts, attach each X2 lead wire to the corresponding conductor. Black-Line, White-Neutral, Green-Ground (see figure 5). - Page 11 Secure Wall Plate Mount to the X2 using the supplied fasteners (see figure 7). Note: If the X2’s button chassis is not aligned with the wall plate mount, remove the mount and adjust the position of the X2. Secure the wall plate mount with the fasteners when satisfied.
-
Page 12: Retrofit Important Notes
The wall box should have a volume of 14 in3 or greater. • The X2 does not have to be on the same circuit as any Ketra fixtures, as all control signals are wireless. • Ketra fixtures to be controlled by the X2 should have an uninterrupted source of power. They should NOT be wired to a light switch or other intermediary device that could cut their power. -
Page 13: X2-Inc Incandescent Dimmer
Prepare the wire for connection to lead wire: A. Strip 0.3 in (8.5 mm) of wire for insertion into the wire nut. B. Twist the stranded wire to prevent fraying (tinning optional). Using the provided wire nuts, attach each X2 lead wire to the corresponding conductor. Black-Line, White-Neutral, Green-Ground, Red-Dimmed Line (see figures 11 & 12). - Page 14 I N S TA L L AT I O N Mount the X2 to the wall box using supplied fasteners (see figure 13). Secure Wall Plate Mount to the X2 using the supplied fasteners (see figure 14). fig. 13 fig. 14 Remove Serial Number Sticker from sheet and affix it to the back of the Wall Plate (see figure 15).
-
Page 15: Retrofit Important Notes
Ketra fixtures being controlled by the X2 Keypad. Ketra fixtures to be controlled by the X2 Keypad do not have to be connected to the same circuit, as the control signal is wireless. However, non-Ketra fixtures will need to be on the same circuit and wired in-line if they are to be controlled by an X2 with onboard incandescent dimmer. -
Page 16: Replacing Button Chassis
To replace the button chassis, follow these steps: Pull airgap switch out. (If X2 already installed) Snap the wall plate off of its mount, and then unscrew and remove the mount. Save screws. Using a Phillips (PH1) screwdriver, unscrew the bottom-right screw that holds the button chassis in place (see figure 10). -
Page 17: Operation
Increase or decrease light intensity. Double tap up or down to go to the max/min intensity of the selected scene. Airgap Switch Pull out to disconnect power to device. 770-000026-01 r12 17 | X2 INSTALLATION GUIDE © 2019 Ketra, Inc. All rights reserved... -
Page 18: Warranty & Tech Support
For questions and technical support please contact: (844) 588-6445 ketrasupport@lutron.com Ketra and KetraNET are trademarks or registered trademarks of Lutron Ketra LLC, in the US and/ or other countries. 770-000026-01 r12 18 | X2 INSTALLATION GUIDE © 2019 Ketra, Inc. All rights reserved... - Page 19 770-000026-01 r12 19 | X2 INSTALLATION GUIDE © 2019 Ketra, Inc. All rights reserved...
- Page 20 6231 E. Stassney Ln. ketra.com Bldg. 13, Suite 400 512.872.4349 Austin, TX 78744 770-000026-01 r12...
Need help?
Do you have a question about the X2 and is the answer not in the manual?
Questions and answers