Handling And Transportation; Assistance And Repairs; Warranty Coverage; Problem Identification - Stiga EL 340 Li 48L Operator's Manual

Make sure the hook and its fastening system are
adequate and able to sustain the machine's weight;
exercise caution and make sure children or animals
do not climb on the machine, weighing down the hook.
Fasten the machine so that the blade faces a wall or is
properly covered, so it is not dangerous in the event of
accidental contact with persons, children or animals.
To store the machine vertically, release the levers (Fig.
47.A) and turn the handle forward so the tooth marked
with «>» matches EXCLUSIVELY with the compartment
marked «S» of the teeth, then lock the levers.
The position must be the same for both sides
8.2 STORING THE BATTERY
The battery must be kept in a cool, shaded place without humidity.
NOTE If unused for any length of time, recharge the
battery every two months to prolong its working life.
9.

HANDLING AND TRANSPORTATION

(Fig.29, Fig. 31, Fig. 34, Fig. 48
The safety regulations to follow are described in
chap. 2. Strictly comply with these instructions to avoid
serious risks or dangers.

10. ASSISTANCE AND REPAIRS

This manual provides all the necessary information to run
the machine and for correct basic maintenance operations
which can be performed by the user. Any regulations and
maintenance operations not described herein must be
carried out by your Dealer or Authorised Service Centre.
Any operations performed in unauthorised centres or by
unqualified persons will totally invalidate the Warranty and
all obligations and responsibilities of the Manufacturer.
• Non-original parts and attachments are not approved;
use of non-original spare parts and attachments
will jeopardize the safety of the machine and relieve
the Manufacturer from all obligations or liabilities.

12. PROBLEM IDENTIFICATION

If problems persist after having performed the above operations, contact your dealer.
PROBLEM
1. The motor does not
start when the switch is
pressed.
÷
53)
PROBABLE CAUSE
Safety key is not inserted or is inserted
incorrectly.
Battery is not inserted or is
inserted incorrectly.
Low battery.
Motor start-up is slow.
The thermal protection has tripped
due to overheating of the motor.

11. WARRANTY COVERAGE

The warranty conditions are intended for consumers
only, i.e. non-professional operators.
The warranty covers all material quality and
manufacturing defects recognised during the warranty
period by your Dealer or Authorised Service Centre.
The warranty is restricted to the repair or replacement
of components recognised as faulty.
It is advisable to send your machine once a
year to an authorised service workshop for
servicing, assistance and safety inspection.
The warranty only applies to machines
subjected to regular maintenance.
The warranty does not cover damages resulting from:
• Failure to become familiar with the documentation
accompanying the machine (Instruction manuals).
• Professional use.
• Carelessness, negligence.
• External causes (lightning, impact, presence of
foreign bodies inside the machine) or incidents.
• Incorrect use or assembly are
prohibited by the manufacturer.
• Poor maintenance.
• Modification to the machine.
• Use of non-genuine spare parts (adaptable parts).
• Use of accessories not supplied or
approved by the manufacturer.
The warranty does not cover:
• The maintenance operations (described
in the instruction manual).
• Normal wear and tear of consumables, such as drive
belts, blade, wheels, safety bolts and cabling.
• Normal wear and tear.
• Deterioration in the appearance of
the machine due to use.
• Blade supports.
• Any ancillary expenses related to the enforcement
of the warranty, such as costs incurred to travel to
the user's location, transfer of the machine to the
Dealer, rental of replacement equipment or calling of
independent enterprises to perform maintenance work.
The user is protected by his or her own national legislation.
The user's rights under the national laws or his or her own
country are not in any way restricted by this warranty.
Insert the key (Fig. 23).
Open the hatch and check that the battery
is fitted in its housing correctly (Fig. 23)
Check the battery status and
recharge if necessary (Fig. 32).
Press and hold the control lever
for 2-3 seconds (Fig. 25).
Wait for at least 5 minutes, then
restart the machine.
EN - 7
SOLUTION