Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for JNE TECH-D
Summary of Contents for JNE TECH-D
- Page 1 Instruction Manual ENGLISH...
-
Page 2: Table Of Contents
Instruction Manual INDEX 1 Introduction 1.1 General.…………………..…..…………. 3 1.2 Maintenance.…………....………… 4 1.3 Warranty………………………….………… 5 2 TECH-D measuring tool 2.1 General description…...…………………... 6 2.2 Display function…..……………………….. 7-10 2.3 Height level rods..………………………… 11 2.4 Magnetic attachment……………………… 11 2.5 Height measuring rods……………………. 11 2.6 Level………………………………………... -
Page 3: Introduction
___________________________________________________________________________ 1 INTRODUCTION 1.1 General Congratulations on your purchase of the TECH-D vehicle measurement tool. TECH-D is an digital measurement tool intended for measuring and checking dimensional accuracy of vehicle unibody and frame. The tool consists the following main components: •... -
Page 4: Maintenance
JNE AB to accurately perform inspections. D. Scrapping When it becomes necessary to scrap any of the TECH-D measuring tool equipment or parts it is essential that every item be sorted for recycling in accordance with local, state and federal requirements. -
Page 5: Warranty
• Equipment has not been modified or rebuilt without the prior approval of JNE AB via its authorized distributor network. • Only genuine TECH-D parts have been used in repairs. Photos and drawings used throughout these instructions depict the fundamental features and... -
Page 6: Tech-D Measuring Tool
___________________________________________________________________________ 2 TECH-D MEASURING TOOL 2.1 General description TECH-D MEASURING TOOL A lightweight telescoping digital measuring arm made up of aluminum and composite materials forms the main component of the tool. In the rear end of the tool is an attachment for height level rods. -
Page 7: Display Function
0 mm. From this point any change in length will register plus or minus in 1 mm gradients. Additional comparative checking is possible by repeating the above procedure at any time during comparative checking. ______________________________________________________________________________ TECH-D manual EN 2010-05-18.doc... - Page 8 SHUT OFF FUNCTION The display will shut down all circuits after 90 minutes of non operation. The measuring arm can also be switched off manually by depressing the button for >3 seconds. ______________________________________________________________________________ TECH-D manual EN 2010-05-18.doc...
- Page 9 ___________________________________________________________________________ Display functions 900-2650 Press > 3 sek Press >2 sek 400-2150 Press <1 Comparative measuring (+ and -) ______________________________________________________________________________ TECH-D manual EN 2010-05-18.doc...
- Page 10 ___________________________________________________________________________ Program menu measuring Comparative measuring < 1 sek > 2 sek > 2 sek ______________________________________________________________________________ TECH-D manual EN 2010-05-18.doc...
-
Page 11: Height Level Rods
“release” mark, set it at the desired height and secure by twisting it to the “lock” position. 2.6 Level LEVEL On the measuring head is a level for comparing divergences in height. ______________________________________________________________________________ TECH-D manual EN 2010-05-18.doc... -
Page 12: Measuring Sockets
NOTE! To change the measuring value to setting 400-2150, press for 2 seconds. It is also important that the height rod is mounted with the value 100 in the lower edge of the measuring head. ______________________________________________________________________________ TECH-D manual EN 2010-05-18.doc... -
Page 13: Change Out Batteries
___________________________________________________________________________ 2.9 Change out batteries The digital circuit of the TECH-D measuring arm is powered by 2 x AA 1.5 Volt batteries. Batteries should be changed out when the digital display begins to flash. It is recommended that both batteries be replaced... -
Page 14: Technical Specification
Extension in mm Change of height in mm approx 0,5 1800 approx 1,0 2650 approx 1,5 Minimum and maximum measuring range. The datum rods’ difference in height = 100 mm ______________________________________________________________________________ TECH-D manual EN 2010-05-18.doc... -
Page 15: Measuring
When in doubt check the above points thoroughly, and if the problem persists, contact the TECH-D distributor or submit your question to our on-line tech support. Refer also to items 3.1 – 3.2. 4.1 Mounting of the magnetic attachment... -
Page 16: Length Measuring
Repeat the same procedure on the other side of the vehicle’s corresponding and selected length measurement point. Note that the vehicle can have different measurement values for the right and left side, depending on the design of the vehicle. ______________________________________________________________________________ TECH-D manual EN 2010-05-18.doc... -
Page 17: Symmetry Measuring
It can be advantageous here to use the hold feature to freeze the measurement value, especially if it is difficult to see the display while measuring. Press the ______________________________________________________________________________ TECH-D manual EN 2010-05-18.doc... - Page 18 (cross) measurement point (measuring line no 3). Note that the vehicle can have different measurement values for the right and left side, depending on the design of the vehicle. ______________________________________________________________________________ TECH-D manual EN 2010-05-18.doc...
-
Page 19: Comparing Heights
• The water level on the TECH-D arm is fixed which often means that it is not on the same level as the vehicle to check. -
Page 20: Position Of The Vehicle
100 200 300 400 500 600 700 800 900 0,5° -3,5 1° 2° 3° The vehicle’s height difference in mm from centre line of vehicle. The degrees show the inclination of the vehicle. Always try to have the vehicle as level as possible. ______________________________________________________________________________ TECH-D manual EN 2010-05-18.doc... -
Page 21: Quick Guide
B. Take a similar length reading the height rod and compare for symmetry. on this side possible datum height C. Compare readings. differences between the two measuring points on opposite sides of the vehicle ______________________________________________________________________________ TECH-D manual EN 2010-05-18.doc... -
Page 22: Adaptors
This also includes the development of different types of adapters, both attachment and measurement adapters. Your local TECH-D distributor will keep you continuously informed of new product innovations. If you have any special preferences or requirements, contact your local TECH-D distributor. -
Page 23: Technical Notes
7 TECHNICAL NOTES 7.1 Spare parts 1:10 M201 M201 Art. No. Name Art. No Name EMK 1900-T Measuring tool AVP1182 Measuring rod 100 EMC 1375 Front AVP1200 Measuring rod 285 EMC 1281 Collar 2 AVP1210 Measuring rod 450 EMC 1291 Collar 3 AVP1110 Datum rod... -
Page 24: Declaration Of Conformity
JNE AB Box 200, S-597 24 Åtvidaberg, SWEDEN Tel: +46 (0)120 109 90, Fax: +46 (0)120 109 40 E-mail: info@jne.se The following standards and/or technical specifications, which comply with good engineering practice in safety matters in force within the EEA,... - Page 25 ___________________________________________________________________________ JNE AB Box 200, S-597 24 Åtvidaberg, SWEDEN Tel: +46 (0)120 109 90, Fax: +46 (0)120 109 40 E-mail: info@jne.se ______________________________________________________________________________ TECH-D manual EN 2010-05-18.doc...
Need help?
Do you have a question about the TECH-D and is the answer not in the manual?
Questions and answers