Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Draytek VigorAP 918R Series
Summary of Contents for Draytek VigorAP 918R Series
-
Page 2: Quick Start Guide
VigorAP 918R Series 802.11ac Outdoor AP Quick Start Guide Version: 1.0 Firmware Version: V1.3.0 (For future update, please visit DrayTek web site) Date: February 5, 2020... - Page 3 Intellectual Property Rights (IPR) Information © All rights reserved. This publication contains information that is protected Copyrights by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. The following trademarks are used in this document: Trademarks Microsoft is a registered trademark of Microsoft Corp.
-
Page 4: Declaration Of Conformity
Declaration of Conformity Hereby, DrayTek Corporation declares that the radio equipment type VigorAP 918R is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.draytek.com.tw/ftp/VigorAP 918R/Document/CE/ Manufacturer: DrayTek Corp. - Page 5 This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antenna/transmitter should be kept at least 20 cm away from human body. More update, please visit www.draytek.com.
-
Page 6: Table Of Contents
1. Package Content ....................1 2. Descriptions of Components................2 3. Mounting the Access Point.................. 3 3.1 Antennas Installation ........................3 3.2 Connecting Ethernet Cable(s)....................4 Reconnecting Ethernet Cable ....................5 3.3 Pole Mount Installation – for VigorAP 918RPD................6 3.4 Pole Mount Installation –... -
Page 7: Package Content
Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. Main Unit Antennas Ethernet Cable (3M) Quick Start Guide Ground Cable & Screws Pipe Clamp Mount Kit (for VigorAP 918RPD) -
Page 8: Descriptions Of Components
AP918R AP918RPD Status Explanation The system is not ready or has failed. Blinking The system is ready. 2.4G / 5G Wireless function is ready. Wireless function is not ready. Blinking Data is being transmitted (sending/receiving). 5G Signal (For D The signal strength (excellent) > -50dBm. Model) 5G Signal (For D The signal strength (good) is between -66dBm ~... -
Page 9: Mounting The Access Point
The VigorAP can be pole mounted depending on the installation environment. This section will guide you through installing the VigorAP. Note For the sake of personal safety, only trained and qualified personnel should install this device. 1. Remove the protective cap. 2. -
Page 10: Connecting Ethernet Cable(S)
Refer to the following steps to attach the Ethernet cable and waterproof head. (Take VigorAP 918RPD as an example.) 1. Remove the cable cover for Ethernet Port (e.g., Port 1 PoE In). 2. Before connecting, verify that the cable has a rubber seal and that it is not damaged. -
Page 11: Reconnecting Ethernet Cable
1. Loosen the thread-lock sealing nut. 2. Loosen the clamping claw and seal. 3. Loosen the body and washer. 4. Remove the cable. 5. To reattach the cable, follow the above steps in reverse. Note The diameter for the Ethernet cable shall be limited between 4.3mm to 5.9mm. -
Page 12: Pole Mount Installation - For Vigorap 918Rpd
– – 1. Find a suitable location for installing the access point. 2. Select a mounting point on a pole. 3. Attach the mount kit assembly to the mounting plate by locking four screws with the torque of 10 kgf-cm. 4. -
Page 13: Pole Mount Installation - For Vigorap 918R
5. Press the pipe clamp to open it for clamping the pole. Note The diameter for a pole shall be limited between 35mm to 60mm. – – Find a suitable location for installing the access point. Select a mounting point on a pole. Insert the pipe clamp on the access point. -
Page 14: Wall Mount Installation - For Vigorap 918R
– – – – Refer to the following steps to mount the access point on the wall. Refer to the following steps to mount the access point on the wall. 1. Find a suitable location for installing the access point. 1. - Page 15 5. Connect the ground rod and the VigorAP using the ground cable. Note Please consult an electrician if you are uncertain about the type of grounding that is required.
-
Page 16: Powering Access Point
VigorAP 918R/RPD can be powered via the PoE input from an in-line power injector or a suitably powered switch port. Before powering VigorAP, you should: Pay attention to local and national electrical codes. Not place the power injector / VigorSwitch in outdoor environment without ... -
Page 17: Connection And Configuration
This section will guide you through the configuration of the settings using a web browser. 1. Make sure your PC is connected to the router correctly. 2. Open a web browser on your PC and type http://192.168.1.2. A pop-up window will open asking you for a username and password. Please type “admin/admin”... -
Page 18: Connected As A Mesh Node (In Mesh Network)
As a mesh node, settings related to VigorAP series must be configured by a remote Mesh Root (e.g., VigorAP 918R) within the mesh network. The user must detect VigorAP 918R series via a Mesh Root to add it as a mesh node. - Page 19 Configure VigorAP. (a) First, open a web browser on your PC and type https://192.168.1.2. A pop-up window will open to ask for username and password. (b) After clicking Login, Quick Start Wizard for configuring wireless settings will appear as follows. (c) Follow the on-screen steps to finish the network connection.
-
Page 20: Customer Service
If the device cannot work correctly after trying many efforts, please contact your dealer/DrayTek for further help right away. For any questions, please feel free to send e-mail to “support@draytek.com”. Web registration is preferred. You can register your Vigor device via http://www.draytek.com.
Need help?
Do you have a question about the VigorAP 918R Series and is the answer not in the manual?
Questions and answers