Related Manuals for Keysight Technologies 8710-2819
Summary of Contents for Keysight Technologies 8710-2819
- Page 1 Keysight Double-Ended for 1.0 mm Torque Wrench Connectors 14 mm Open End, 4 lb-in (0.45 Nm) and 10 lb-in (1.13 Nm) Part Number: 8710-2819 User’s Guide...
- Page 2 THESE TERMS, THE WARRANTY beyond those set forth in the TERMS IN THE SEPARATE EULA shall apply, except to the © Keysight Technologies, Inc. 2020 AGREEMENT WILL CONTROL. extent that those terms, rights, or No part of this manual may be...
-
Page 3: Table Of Contents
Contents Table of Contents Available Accessories ................5 Introduction. - Page 4 Contents Keysight Double-Ended Torque Wrench User’s Guide...
-
Page 5: Available Accessories
Figure 1 Dual Torque wrench, 14 mm open end, 4 lb-in (0.45 Nm) and 10 lb-in (1.13 Nm), Part Number 8710-2819 FOR KEYSIGHT RUGGED 1mm MATING CONNECTORS ONLY FRONT... -
Page 6: Test Port Connector
Test Port Connector Figure 2 shows the torque specification for the two connection threads on the N5293/95AXxx front-panel test port connectors. Two wrenches must be used to avoid stress on cables. Figure 2 Torque Specification for Test Port Threads 10 lb-in torque (outer threads) 4 lb-in torque (inner threads) -
Page 7: Test Port Adapters
Test Port Adapters These adapters can be connected to the N5293/95AXxx’s test ports. Due to the physical requirements needed to obtain high performance, the geometry of these, as well as all 1.0 mm connectors, demands special care to avoid expensive damage as explained in this document. Figure 3 Ruggedized Adapters Keysight Double-Ended Torque Wrench User’s Guide... -
Page 8: Making Rf Connections
Making RF Connections 1. Work at a static-safe workstation. 2. Visually inspect the connectors. If necessary, clean the connectors. Carefully align the connectors. The male connector center pin must slip concentrically into the contact fingers of the female connector. 3. Push the connectors straight together. 4. -
Page 9: Applying Torque
Applying Torque For the 1.0 mm Test Port connectors, use the dual torque wrench. For torquing non-ruggedized connectors using the inner threads to the N5293/95AXxx’s, use the 4 lb-in silver end of the torque wrench as shown in Figure 4 Figure For torquing ruggedized connectors using the outer threads to the N5293/95AXxx’s, use the 10 lb-in red end of the torque wrench as shown in... -
Page 10: Selecting And Positioning The Wrenches
8 mm wrench on the flats that are adjacent to the knurled ring. Figure 5 Wrenches Positioned on Correct Flats Groove marks the correct place to hold wrench Torque wrench 8710-2819 10 lb-in 8 mm open end wrench torque wrench N1060-20009 red end... -
Page 11: Non-Ruggedized Adapter To Test Port
Confirm also that your adapter or test port can withstand 4 lb-in. Figure 6 Wrenches Positioned on Correct Flats Groove marks the correct place to hold wrench Torque wrench 8710-2819 7 mm open-end 4 lb-in wrench torque wrench 8710-1761... - Page 12 This information is subject to change without notice. © Keysight Technologies 2020 Edition 1, January 2020 5972-4085 www.keysight.com...
Need help?
Do you have a question about the 8710-2819 and is the answer not in the manual?
Questions and answers