Related Manuals for Gravely Ariens 815134
Summary of Contents for Gravely Ariens 815134
- Page 1 Zoom & ZT Bagger Owner/Operator Manual Models 815134 – 34” Bagger (SN 00101 +) 815142 – 42” Bagger (SN 00101 +) 815150 – 50” Bagger (SN 00101 +) 04725000A 6/16 Printed in USA...
-
Page 2: Table Of Contents
THE MANUAL PRODUCT REGISTRATION Before operation of unit, carefully and completely read The Ariens/Gravely dealer must register the product at this Manual and the unit’s Owner/Operator Manual. The the time of purchase. Registering the product will help the contents will provide you with an understanding of safety... -
Page 3: Safety
3. Review control functions and operation of the unit. www.ariens.com on the internet. To locate your nearest Do not operate unit unless all controls function as Gravely Dealer, go to www.gravely.com on the internet. described in this manual. 4. Review recommended lubrication, maintenance WARNING: Improper assembly or adjustments and adjustments. - Page 4 Operator Age 1. WARNING! DO NOT allow children under the age of 18 to operate any outdoor power equipment. Stop engine and wait for all moving parts to Local regulations may restrict the age of the operator. stop before opening cover. Data indicates operators age 60 years and above are involved in a large percentage of riding mower-related Avoid tip over and loss of control:...
- Page 5 NEVER operate bagger if the unit’s safety interlock DO NOT operate machine while feeling tired, ill or under system is not working properly. the influence of alcohol or drugs. Ensure that tires are inflated to recommended pressure. DO NOT put hands or feet near rotating parts or under the machine.
- Page 6 DO NOT mow near drop-offs, ditches, or embankments. Operating Conditions The machine could suddenly roll over if a wheel goes Lightning can cause severe injury or death. If lightning is over the edge or if the edge caves in. seen or thunder is heard in the area, do not operate the DO NOT bypass transmission or allow transmission to machine, seek shelter.
- Page 7 Lower cutting deck unless a positive mechanical lock is Accessories used. Follow the manufacturer’s recommendation for wheel Allow engine to cool before servicing. weights or counterweights Moving parts can cut or amputate fingers or a hand. On Check grass catcher components and the discharge multiblade mowers, rotation of one blade will cause all guard frequently and replace with manufacturer’s blades to rotate.
-
Page 8: Assembly
ASSEMBLY Part Item Description WARNING: AVOID INJURY. Read and Number understand the entire Safety section before Receiver & Hardware proceeding. Bag Frame 00663200 Plastic Tube, 3/8 x 1/2 x 3" 00677000 UNPACKING UNIT Footrest 04188353 IMPORTANT: Remove contents from carton carefully. Tube 04192901 Place cover assembly on a flat piece of cardboard to... - Page 9 Secure with two 5/16 nyloc flange nuts. Adhere the Ariens SN 030000 + grip adhesive (item 3) just above the two bolts Ariens & Gravely SN 029999 & Below (item 5) on the footrest. See Figure 5. WARNING: ALWAYS install counterweight before operating unit with bagger attached.
- Page 10 2. Use the red footrest (item 25) that is included in the kit, and lay the footrest onto the back of the weight tray (similar profile). It may be helpful to have the weight tray laying upside down on the ground when mating it to the footrest.
- Page 11 Discharge Chute Boot Bracket Front Deck Bolt Front Boot Hole Bagger Boot Rear Deck Bolt Boot Notch Connect rear boot strap to deck post. Connect rear boot strap to deck post. Connect front boot strap to Connect front boot strap to deck post.
- Page 12 3/8 x 1" Hex Bolt & 3/8" Locking Nut L Bracket Hood Assembly Receiver Figure 12 Figure 10 5. Position bagger support bar inside of engine control cables and attach support bar to L bracket using 1/2 2. Insert L bracket into the receiver and fasten using x 2 3/4"...
- Page 13 6. Mount front of support bar to the mower frame Thread bag frame (item 23) through sleeve in mesh using 3/8 x 3/4" clevis pin, 3/8" washer and bow-tie bag (item 2). locking cotter pin. (The bar must be on the inside of the frame, as shown in Figure 14.) Tighten hardware installed in step 5.
- Page 14 3. Install mesh bags to bagger frame. Make sure that Thumb Latch the heat-resistant side of the mesh bags faces the unit. See Figure 16. The heat resistant side (smooth side) MUST face the unit. Mesh Bags Figure 16 Bagger Hose Figure 18 4.
-
Page 15: Removal
When the airflow indicator is facing forward, the air is 1. Check bagger parts for wear, deterioration, or unrestricted, indicating that the grass bagger baskets are damage. Replace ONLY with Ariens/Gravely not full and there are no clogs in the bagger. original service parts before operating. -
Page 16: Maintenance
MAINTENANCE WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. Ariens/Gravely Dealers will provide any service or adjustments which may be required to keep your unit operating at peak efficiency. Interval Task Action... -
Page 17: Storage
SPECIFICATIONS STORAGE Model Number 815134 WARNING: AVOID INJURY. Read and Description Non-Powered Bagger understand the entire Safety section before Serial Number 000101 + proceeding. Added Length to Unit 19 5/8 in. (49.8 cm) IMPORTANT: NEVER spray unit with high-pressure Added Width to Unit 10 in. -
Page 18: Parts List
PARTS LIST SAFETY DECALS BOM/ID Number Description 05359700 Decal, Bagger Cover 07897700 Decal, Boot Caution... - Page 19 BAGGER HOOD PREASSEMBLED IN KIT 51577800 BOM ID Number Qty Description BOM ID Number Qty Description 04409600 COVER, 2-BUCKET BAGGER 06536000 NUT-LK-NYL #10-24 YWZC 04409900 SEAL, UPPER BOOT 06714800 PIN-HAIR, ENDRIES #25 YWZC 04410051 WLDMT, BAGGER HOOD VENT, LH 06800108 RVT-POP .187x.375 04410700 SEAL, BULB - BAGGER HOOD...
- Page 20 BAGGER LOWER BOOT MODEL 815134 MODEL 815142 PREASSEMBLED IN KIT 51577500 PREASSEMBLED IN KIT 51577600 BOM ID Number Qty Description 04392000 BOOT, BAGGER ,42" TUNNEL DECK 04449651 WLDMT, BOOT 42" ZOOM/ZT 04513051 BRKT, BOOT REINFORCEMENT BOM ID Number Qty Description 06116900 SCR-MCH 10-24X.75 HWH YWZC 04433200...
- Page 21 BAGGER FRAME BOM ID Number Description BOM ID Number Description 03844151 1 OVERLAP PLATE, BAGGER FRAME 06436200 1 WSHR-FL-STL.406X.812X.065 YWZ 04795751 1 ASM, BAGGER FRAME UPPER 06442700 3 WSHR-FL-STL.219X.500X.049 YWZC 04409751 1 BRKT, RECEIVER SLEEVE INSERT 06500010 1 NUT-LK-NYL-FLG .50-13 YWZC 04409851 1 BRKT, RECEIVER LOWER 06545500 2...
- Page 22 COUNTERWEIGHT ASSEMBLY BOM/ID Number Description 04215451 Weldment, Bagger Weight Tray 00172000 Cast Iron Weight 06200205 Bolt, Round Head Square Neck 1/2-13 x 2.00 06216100 Bolt, Round Head Square Neck 1/2-13 x 1.00 03833800 Grip, Adhesive 05957800 Bolt, Hex 3/8-16 x 3.00 06308800 Washer, Lock 3/8 06545400...
-
Page 23: Warranty
Limited Warranty Warranty Ariens Company (Ariens) warrants to the original purchaser that Ariens, Gravely and Countax brand lawn and garden consumer products purchased on or after 9/1/2015 will be free from defects in material and workmanship for the time period noted in the chart below. - Page 24 • Perform the maintenance and adjustments explained in the owner's manual. • Promptly notify Ariens or an authorized Ariens, Gravely or Countax service representative of the need for warranty service. • Transport the product to and from the place of warranty service at owner's expense.
- Page 26 Ariens Gravely 655 West Ryan Street Brillion, WI 54110-1072 920-756-4688 Fax 920-756-2407 www.ariens.com www.gravely.com...
Need help?
Do you have a question about the Ariens 815134 and is the answer not in the manual?
Questions and answers