Related Manuals for TYROLIT Hydrostress HYDROSTRESS FGE 450
Summary of Contents for TYROLIT Hydrostress HYDROSTRESS FGE 450
- Page 1 10999145_en Floor grinding machine FGE 450 ......Translation of the original operating manual...
- Page 2 Fig. E Fig. A Fig. F Fig. G Fig. B Fig. H Fig. I Fig. C Fig. J Fig. K Fig. D...
-
Page 3: Table Of Contents
Publishing date: 16.01.2018 A/F Carrier handle TYROLIT Hydrostress AG Safety hood TYROLIT Hydrostress AG reserves all rights. Any reproduction, use or distribution of this original opera Dust cover ting manual or the translations of the original opera Velcro strip... -
Page 4: Important Notes
EN Floor grinding machine FGE 450 1 Important notes 1 Important notes 1.2 Liability and warranty TYROLIT Hydrostress AG The machine may be used only with the accessories All rights, including those pertaining to translation, lie supplied by the manufacturer for stripping, wet grin... -
Page 5: Safety Instructions
EN Floor grinding machine FGE 450 2 Safety All laws and regulations (e.g. the valid regulations on waste disposal), accident prevention guidelines and generally recognised safety rules must be complied with when working on and with the machine. Risk of injury from rotating machine parts! Limbs and clothing can be drawn in. -
Page 6: Operating
EN Floor grinding machine FGE 450 3 Operating Cleaning and maintenance may be done only by trained personnel. Maintenance must be conducted according to the operation manual. Do not use high pressure cleaners to clean the Risk of injury from dust formation during grin machine! ding work! Connect an extractor unit to the machine or feed... -
Page 7: Operation
EN Floor grinding machine FGE 450 3 Operating For transporting the machine, the guide handle Activate and secure the safety switch can be swivelled to the front position. [12, Fig. B]. Close the clamping lever (Fig. E). Press the green ON switch [15, Fig. B]. The guide handle is locked. -
Page 8: Maintenance
EN Floor grinding machine FGE 450 4 Maintenance 4 Maintenance 4.3 Mounting and dismantling ETX diamond tools The consistency of the surface to be ground determines Observe the safety instructions in Chapter 2! the type or composition of the tools to be used. All ETX diamond tools authorised for this ma... -
Page 9: Mounting The Etx Locating Plate
EN Floor grinding machine FGE 450 5 Acceptance and transportation 5 Acceptance and transportation 4.5 Mounting the ETX locating plate Tilt the machine (! Chapter 4.2). Observe the safety instructions in Chapter 2. Push the ETX locating plate [25, Fig. K] onto the guide bolts and screw tight with the central fixing 5.1 Machine acceptance screw M8x20 [28, Fig. -
Page 10: Technical Data
EN Floor grinding machine FGE 450 6 Technical data Suspended loads can fall or tip over, causing If necessary (e. g. for lorry transport), serious injuries! screw the 4 screws [20, Fig. F] tightly and fasten all loose parts on the frame. Move drive and frame to the respective lo... - Page 11 EN Floor grinding machine FGE 450 7 Troubleshooting 7 Troubleshooting Only suitably knowledgeable, qualified profes sional technicians may perform repairs on the machine. Malfunction Cause Rectification Machine will not start. The voltage supply has not been Join the connecting cable (extension properly connected.
-
Page 12: Declaration Of Conformity
EN Floor grinding machine FGE 450 8 Declaration of Conformity 8 Declaration of Conformity TYROLIT Hydrostress AG Witzbergstrasse 18 CH-8330 Pfäffikon ZH Switzerland We hereby declare that the machine FGE 450 complies with the provisions described in — Directive 2006/42/EG Machine —... - Page 14 TYROLIT Hydrostress AG Witzbergstrasse 18 CH-8330 Pfäffikon ZH Switzerland Telefon: +41 (0)44 952 18 18 Telefax: +41 (0)44 952 18 00 URL: www.tyrolit.com...
Need help?
Do you have a question about the HYDROSTRESS FGE 450 and is the answer not in the manual?
Questions and answers