Advertisement
C
ontents
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Before Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Note: Please read and understand these Assembly Instructions for the Legacy Basic Acoustical
Shell before assembling the parts.
Note: Refer to the illustrations on the following pages. If you need additional information, write or
telephone Wenger Corporation at the number below.
©Wenger Corporation 2011
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Questions? Call.....USA: 800-4WENGER (493-6437) • Worldwide: 1-507-455-4100 • www.wengercorp.com
Legacy
Basic Acoustical Shell
®
Printed in USA 09/11
Assembly Instructions
Part #186H564-02
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Wenger Legacy Basic Acoustical Shell
Summary of Contents for Wenger Legacy Basic Acoustical Shell
- Page 1 Note: Refer to the illustrations on the following pages. If you need additional information, write or telephone Wenger Corporation at the number below. ©Wenger Corporation 2011 Printed in USA 09/11 Part #186H564-02 Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448 Questions? Call..USA: 800-4WENGER (493-6437) • Worldwide: 1-507-455-4100 • www.wengercorp.com...
- Page 2 Afety reCAUtIons Throughout this manual you may find cautions and warnings which are defined as follows. • WArNiNg means that failure to follow the instruction may result in serious injury or death. • CAutioN means that failure to follow the instruction may result in serious injury or damage to property.
- Page 3 The following tools are required to assemble the Legacy Basic Acoustical Shell: " Wrench " Open End Combination Wrench • • " Wrench Utility Knife (to cut plastic wrap and banding) • • efore ssembly Units should be assembled indoors, in a well-lighted space with a level floor. Choose an area close to the performance space - a backstage scene shop is ideal.
- Page 4 ssembly 1. Remove the Hardware Bag and check the contents. It should contain the following: Casters, 3 x 2” Wide -16 x 2- " Capscrew -16 Lock Nut 2. Remove the screws securing the two wood blocks to the pallet. Discard the wood blocks.
- Page 5 ssembly ContInUed 4. Unbolt and remove the screws and brackets securing the Shell to the pallet. Bolts and Bracket 5. Slide the shell over until the closed ends of both Feet extend beyond the edge of the pallet. Locate the two Casters in the Hardware Pack and screw each one into the threaded hole on the underside of each foot.
- Page 6 ssembly ContInUed 6. Slide one Plug-In Foot Assembly into the open end of one of the feet and align both sets of pre-drilled holes. From the top, insert one -16 x 2- " Capscrew through each set of pre-drilled holes and secure at the bottom with a -16 Lock Nut.
- Page 7 ssembly ContInUed 8. Remove any remaining cardboard, banding, tape and packaging. For operating instructions and replacement parts information, refer to the owner’s Manual.
- Page 8 This page is intentionally blank.
Need help?
Do you have a question about the Legacy Basic Acoustical Shell and is the answer not in the manual?
Questions and answers