Channel Master 3010 Instruction Sheet

Front End
Front End
Front End
VHF element
VHF element
LEFT RIGHT
LEFT side
SIDE SIDE
LEFT RIGHT
LEFT RIGHT
SIDE SIDE
SIDE SIDE
Main Unit 4 - M6 x 12mm
(bottom view) self tap screws
Main Unit
4 - M6 x 12mm
Main Unit 4 - M6 x 12mm
(bottom view) self tap screws
(bottom view) self tap screws
Hardware Bag
2 - M4 x 10mm self tap screws
Hardware Bag
Hardware Bag
4 - M6 x 12mm self tap screws
2 - M4 x 10mm self tap screws
2 - M4 x 10mm self tap screws
1 - mounting nest
4 - M6 x 12mm self tap screws
4 - M6 x 12mm self tap screws
1 - mounting nest
1 - mounting nest
I F G U R E A
I F G U R E A
I F G U R E A PCB
VHF slots
in housing
VHF slots
VHF slots
in housing
in housing
LEFT SIDE INSIDE VIEW
I F G U R E C
LEFT SIDE INSIDE VIEW
LEFT SIDE INSIDE VIEW
I F G U R E C
Four M6 x 12mm
screws and M6
external tooth
lockwashers from
hardware bag
Four M6 x 12mm
screws and M6
external tooth
lockwashers from
hardware bag
"F" Connector
"F" Connector
Standout
Standout
VHF element VHF element
LEFT side RIGHT side
VHF element
VHF element
LEFT side RIGHT side
RIGHT side
2 - M4 x 10mm
self tap screws
2 - M4 x 10mm
2 - M4 x 10mm 4 - M6 external
self tap screws
self tap screws tooth lockwashers
2 - M6 x 70mm hex head bolts
(cover)
2 - M6 flat washers
(VHF elements)
(cover) 2 - M6 x 70mm hex head bolts
2 - M6 x 70mm hex head bolts
(cover)
(mast) 1 - rubber weather boot
2 - M6 flat washers
(VHF elements)
(VHF elements) 2 - M6 flat washers
4 - M6 external tooth lockwashers
(mast) 1 - rubber weather boot
1 - rubber weather boot
(mast)
4 - M6 external tooth lockwashers
4 - M6 external tooth lockwashers
PCB
PCB
VHF element
to slide
VHF element
under PCB
VHF element
to slide
to slide
under PCB
under PCB
Recess for Slide element slot in all of
I F G U R E D
Slide element slot in all of
snap fit the way (2 slots per element)
the way (2 slots per element)
Cover
Recess for
I F G U R E D
snap fit
Cover
Cover
Tabs (2)
Cover
Tabs (2)
Mast
Nest/Bolts
Mast
Ground Block
Tape/Cable Tie
Nest/Bolts
Ground Block
Tape/Cable Tie
4 - M6 external
tooth lockwashers
4 - M6 external
tooth lockwashers
I F G U R E B
I F G U R E B
I F G U R E B
Pre-installed
screw (halfway
Pre-installed
turned down "4")
Pre-installed
screw (halfway
screw (halfway
turned down "4")
turned down "4")
Line up the holes
in the element with
Line up the holes
Line up the holes the holes in the
in the element with
mounting bosses
in the element with
the holes in the
the holes in the
mounting bosses
mounting bosses
Slide element slot in all of
the way (2 slots per element)
Inside Housing
Bosses for
M4 x 10mm
screws (2)
Inside Housing
Cover tab
slots (2)
Bosses for
M4 x 10mm
screws (2)
Inside rear wall
Cover tab
slots (2)
Inside rear wall
Ground Rod
Ground Rod