Advertisement
4. installation
warning! The inflator is designed for indoor use only.
‰
4.1.
The compressor producing the air should have the necessary water and
dirt filtration, to minimise accumulation of debris at the inflator line
filter strainer.
4.2.
installation:
4.2.1.
Qube is design to be mounted to a wall/support at 90°.
4.2.2.
Affix the 2 metal brackets to the rear of Qube, place the assembly
to the wall. Mark the holes, mount the Qube using adequate screwed
support.
ensure the Mains plug can be easily accessed at all times.
9
5. calibration & accuracy
5.1.
The accuracy of our digital units when released from our factory is
that:-
5.1.1.
The maximum permissible error (MPE) = 0.08 bar.
5.1.2.
each unit, before release, is checked and calibrated on test equipment
that has accuracy traceable national standards.
6. oPeration
6.1.
control Panel
note:
All QUBE models have a filter housing of G1/4.
6.1.1.
It is recommended that when tightening any hose connections
to the QUBE, the user selects two spanners. Hold the filter
housing with one spanner, to ensure it does not spin, then
tighten the hose connection with the other.
6.2.
MoDe overview
6.2.1.
The unit has a choice of 3 different inflator applications installed.
6.2.2.
Your QUBE can be configured into the 3 different applications.
6.2.3.
Application Modes:-
stanDarD (std)
The QUBE will inflate and deflate tyres (Default mode by Sealey).
tyre shoP (tir)
The QUBE will inflate and deflate tyres and will allow Over
Pressure Setting (oPs).
n2 (n2P)
The QUBE will inflate and deflate tyres and allow tyre purging
for Nitrogen rich tyre filling.
during the start up procedure initiation the current application is always shown.
6.3.
start-uP
6.3.1.
On plugging in the unit for the first time, the QUBE will automatically start in Standard (std) operation.
6.3.2.
However, if the Tyre Shop (tir) or N2 (n2P) operation are required, then follow the Application Mode Selection.
6.3.3.
The QUBE will reboot into the desired application and will remain in this mode until an alternative mode is selected with Application
Mode Selection.
6.4.
stanDarD (stD) oPeration: inflation anD Deflation
6.4.1.
Set desired pressure, by touching either
6.4.2.
Connect the hose to the tyre.
6.4.3.
Automatic inflation will commence to the set pressure, periodically stopping to display the pressure of the tyre.
6.4.4.
If the pressure in the tyre is below 3 psi, 0.2 bar the process will not commence until
6.4.5.
When the Set pressure is reached, the buzzer will sound and the display will show 'enD' with the final pressure. Red LED light
will flash.
6.4.6.
Remove the hose from tyre.
6.4.7.
For selection of alternative pressure unit touch
6.4.8.
For adjustments to Inflators parameters please refer to your Distributor or Sealey.
warning! This unit is not suitable for the filling of bicycle tyres with a standard (Presta, Woods) bicycle valves and adapters.
‰
Over fill of the tyre is possible!
6.5.
aDjustMent of the favourite setting for all oPerational MoDes
6.5.1.
Select the desired favourite pressure set value using
6.5.2.
Hold
button until beep is heard (3 seconds)
6.5.3.
Press to select your favourite, this may be altered by resetting.
6.5.4.
Repeat
for
, and
note:
These values are retained after power down.
6.6.
aPPlication MoDe selection
6.6.1.
Turn on power supply.
6.6.2.
display will show all lCd digits check.
6.6.3.
Display will show the current Firmware version number e.g. '.3.2.5'.
6.6.4.
Display will show Program model variant '415'.
6.6.5.
display will show the current application, 'std' , 'tir' or 'n2P' as stored.
After 10 seconds the display will show 'Pcl'.
6.6.6.
6.6.7.
Touch
to enter Application Mode.
6.6.8.
display will show 'l 0', confirm to enter by touching
6.6.9.
display will show 'aPP' confirm to enter by touching
© Jack Sealey limited
or
and
is now saved to your favourite setting.
Original Language Version
fig.2
is touched.
SA390 Issue 1 02/07/19
fig.1
Advertisement
