Table of Contents
Advertisement
Quick Links
an ISO 9001:2015 Registered Company
1969-70 Mopar B-Body
without Factory Air
Evaporator Kit
571064
Fits:
Dodge: Coronet, Super Bee, Charger
Plymouth: Satellite, Road Runner, GTX
18865 Goll St. San Antonio, TX 78266
Phone: 800-862-6658
Sales: sales@vintageair.com
Tech Support: tech@vintageair.com
www.vintageair.com
901304 REV D 02/28/2017, PG 1 OF 23
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Vintage Air 571064
Summary of Contents for Vintage Air 571064
-
Page 1: Cover
ISO 9001:2015 Registered Company 1969-70 Mopar B-Body without Factory Air Evaporator Kit 571064 Fits: Dodge: Coronet, Super Bee, Charger Plymouth: Satellite, Road Runner, GTX 18865 Goll St. San Antonio, TX 78266 Phone: 800-862-6658 Sales: sales@vintageair.com Tech Support: tech@vintageair.com www.vintageair.com... -
Page 2: Table Of Contents
Table of Contents www.vintageair.com Cover..........................Table of Contents......................Packing List/Parts Disclaimer..................... Information Page....................... Wiring Notice........................Engine Compartment, Condenser Assembly & Installation, Compressor & Brackets, Pulleys..........................Passenger Compartment Disassembly................Defrost Duct Hose Adapter & Cowl Cover Installation, Evaporator Bracket, Evaporator Hardline & Heater Hose Fitting Installation..............Evaporator Bracket, Evaporator Hardline &... -
Page 3: Packing List/Parts Disclaimer
Accessory Kit, 69-70 Mopar B-Body without A/C ** Before beginning installation, open all packages and check contents of shipment. Please report any shortages directly to Vintage Air within 15 days. After 15 days, Vintage Air will not be responsible for missing or damaged items. -
Page 4: Information Page
Refrigerant Capacities: Vintage Air System: 1.8 lbs. (28.8 oz.) or 816 grams of R134a, charged by weight with a quality charging station or scale. NOTE: Use of the proper type and amount of refrigerant is critical to system operation and performance. -
Page 5: Wiring Notice
Vintage Air strives to harden our products against these types of electrical noise, but there is a point where a vehicle’s electrical system can be degraded so much that nothing can help. -
Page 6: Pulleys
Engine Compartment Disassembly www.vintageair.com NOTE: Before starting the installation, check the function of the vehicle (horn, lights, etc.) for proper operation, and study the instructions, illustrations, & diagrams. Perform the Following: Disconnect battery. Remove battery (retain). Drain radiator. Remove OEM heater hoses (discard). Remove OEM blower assembly (discard). -
Page 7: Passenger Compartment Disassembly
Passenger Compartment Disassembly www.vintageair.com Perform the Following: Remove glove box (1969 models: Discard, but retain OEM screws)(1970 models: Retain glove box and screws). Disconnect all wires and cables from OEM control panel (discard). Remove OEM control panel assembly (discard). Remove OEM duct hoses from defrost ducts (discard). Remove OEM fresh air duct (discard). -
Page 8: Defrost Duct Hose Adapter & Cowl Cover Installation, Evaporator Bracket, Evaporator Hardline & Heater Hose Fitting Installation
Defrost Duct Hose Adapter & Cowl Cover Installation www.vintageair.com 1. Install (2) S-clips onto defrost duct hose adapters (See Figure 4, below). 2. Install defrost duct hose adapters onto OEM driver and passenger side defrost ducts as shown in Figure 4, below. -
Page 9: Evaporator Bracket, Evaporator Hardline & Heater Hose Fitting Installation (Cont.)
Evaporator Bracket, Evaporator Hardline & Heater Hose Fitting www.vintageair.com Installation (Cont.) ECU Module (2) 1/4-20 X 1/2” Hex Bolts Hold With This Wrench Twist With This Wrench Rear Lubricate O-ring Evaporator Bracket (See Figure 12, (2) 1/4-20 x 1/2” Page 13) 643099 Hex Bolts Figure 6... -
Page 10: Firewall Cover Installation, Firewall Modification
Firewall Cover Installation www.vintageair.com If applicable, remove OEM wire clamp from firewall (See Figure 7, below), and ensure firewall surface is smooth. Using firewall cover as a template, mark and drill (4) 3/8” holes in firewall (See Figure 7, below). Apply a 1/4”... -
Page 11: Evaporator Installation
NOTE: To ensure a watertight seal between the passenger compartment and the vehicle exterior, for all bolts passing through the firewall, Vintage Air recommends coating the threads with silicone prior to installation. Install A/C and heater hoses (See Figure 9a, below). -
Page 12: Inner Fender Cover & Hardline Installation
Inner Fender Cover & Hardline Installation www.vintageair.com Remove OEM caster/camber access panel from passenger side wheel well (discard) (See Figure 10, below). Install (4) grommets in inner fender cap (See Figure 10a, below). Install inner fender cap in wheel well side using (2) #10 x 1/2” sheet metal screws as shown in Figure 10a, below. -
Page 13: Drain Hose Installation, Lubricating O-Rings, A/C Hose Installation
Drain Hose Installation www.vintageair.com Locate evaporator drain on bottom of evaporator case. In line with drain, measure 1” down and 2” to the left, and drill a 5/8” hole through the firewall (See Figure 11, below). Install drain hose to outlet on bottom of evaporator unit, and route through the firewall. -
Page 14: Heater Hose & Heater Control Valve Installation, A/C & Heater Hose Routing
Heater Hose & Heater Control Valve Installation 1. In engine compartment, route a piece of heater hose from the water pump to the top heater fitting on the inner fender cap (See Figure 13, below). Secure using hose clamps. 2. In engine compartment, route a piece of heater hose from the intake to the bottom heater fitting on the inner fender cap (See Figure 13, below). - Page 15 Driver Side Under Dash Louver Installation www.vintageair.com 1. Place driver side louver housing under dash. Mark and drill (2) 9/64” holes as shown in Figure 14, below. 2. Secure louver housing to dash using (2) #10 x 1/2” hex sheet metal screws as shown in Figure 14, below. 3.
-
Page 16: Final Steps
12. Double check all fittings, brackets and belts for tightness. 13. Vintage Air recommends that all A/C systems be serviced by a licensed automotive A/C technician. 14. Evacuate the system for a minimum of 45 minutes prior to charging, and perform a leak check prior to servicing. -
Page 17: Control Panel & Duct Hose Routing
Control Panel www.vintageair.com & Duct Hose Routing From Control Panel Passenger Side Plug Defrost Duct From 2” x 12” Control Wiring Harness 232002-VUA Driver Side Defrost Duct 2” x 20” Driver Side Plug Center Louver From 2 ½” x 25” Wiring Harness 232600-VUA... -
Page 18: Wiring Diagram
Wiring Diagram www.vintageair.com 232007-VUR AC ANNUNCIATOR BACKLIGHT POS BACKLIGHT NEG 5V-SW WHT/RED TEMP WIPER WHT/YEL MODE WIPER WHT/GRN FAN WIPER PRE-WIRED VIEWED FROM WIRE SIDE GEN IV ECU 232002-VUA GEN IV WIRING DIAGRAM (IF USED) REV E, 10/6/2017 TEMP MODE PROGRAM * DASH LAMP (IF USED) -
Page 19: Gen Iv Wiring Connection Instructions
HARNESS TERMINAL) HARNESS ARE NOT IGNITION USED. Dash Light: YELLOW SWITCH ORANGE Tan Wire Used Only With Vintage Air Supplied Control Panel With LED Back DASH BACK LIGHT+0-12v Light. GRAY GRAY WIRE IS USED FOR PROGRAMING CONTROLS IF APPLICABLE GREEN... -
Page 20: Operation Of Controls
www.vintageair.com Operation of Controls On Gen IV systems with three lever/knob controls, the temperature control toggles between heat and A/C operations. To activate A/C, move the temperature lever/knob all the way to cold and then back it off to the desired vent temperature. -
Page 21: Troubleshooting Guide
901304 REV D 02/28/2017, PG 21 OF 23... -
Page 22: Troubleshooting Guide (Cont.)
901304 REV D 02/28/2017, PG 22 OF 23... -
Page 24: Packing List
Packing List Evaporator Kit (571064) www.vintageair.com Qty. Part No. Description 744004-VUE Gen IV Evaporator Sub Case w/ 204 ECU 781075 Accessory Kit, 69-70 Mopar B-Body without A/C Checked By: Packed By: Date: Gen IV Evaporator Sub Case w/ 204 ECU...
Need help?
Do you have a question about the 571064 and is the answer not in the manual?
Questions and answers