Pairing Bluetooth Devices - Philips CEM250/55 Quick Start Manual

Overview of parts 1
These are the supplied parts needed to
connect and install this unit.
1 In-car audio system
2 Sleeve
3 Front panel
4 Standard connector
5 Trim plate (2 pieces)
6 Rubber cushion
7 Disassembly tools
8 Screws 4 pieces
Connect wires
Caution
Ensure that all loose leads are insulated with
•
electrical tape.
2 3
For cars with ISO connectors
1
Pull out the ISO connectors from car
dashboard and connect them to the bigger
end of the supplied standard connector.
2
Connect the other end of the supplied
standard connector to the unit.
3
Connect the antenna and amplifi er as
illustrated, if applicable.
Connector Connect to
1 MIC Microphone
2 REAR LINE Rear right
OUT R speaker
3 REAR LINE Rear left speaker
OUT L
4 SUB OUT Subwoofer
5 ANTENNA Antenna
3 4
For cars with ISO connectors
Caution
• Be sure to connect the black ground (earth)
lead fi rst.
1
Connect the antenna and amplifi er as
illustrated, if applicable.
2
Cut off the bigger end of the supplied stan-
dard connector.
3
Check the car's wiring carefully and connect
them to the supplied standard connector.
4
Connect the supplied standard connector to
the unit.
1 Green/black Left speaker
strip (Rear)
2 White/black Left speaker
strip (Front)
3 Gray/black Right speaker
strip (Front)
4 Purple/black Right speaker
strip (Rear)
e RED Ignition key +12V DC
when ON/ACC
f BLUE Motor/electric antenna
relay control lead/
Amplifi er relay control
lead
g BLACK Ground
h Orange/ Illumination switch
white
i YELLOW To the +12V car battery
which is energized at all
times
Note
Check wire connection before you mount
•
the unit into a car.
If preset radio stations are lost when the
•
ignition key is turned OFF and then back
ON, reconnect the red leads crosswise to
the yellow ones.
Mount in the dashboard 5
1
If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
• If you disconnect the car battery in a car
that has an on-board drive or navigation
computer, the computer may lose its
memory.
• If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
wires do not touch each other.
2
Remove the two screws on the top of the
unit.
3
Remove the mounting sleeve with the
supplied disassembly tools.
4
Install the sleeve into the dashboard and
bend the tabs outward to fi x the sleeve.
5
Place the rubber cushion over the end of
the bolt.
6
Slide the unit into the dashboard until you
hear a click sound.
7
Reconnect the negative terminal of the car
battery.
Attach the front panel 5
1
Attach the trim plate.
2
Insert the right side of the panel in the
chassis until it is correctly engaged.
3
Press the left side of the panel and point
the left hole at the left pillar.
4
Release the panel to engage the left side.
Turn on
1
Press z to turn on the unit.
• To turn off the unit, press z for 3
seconds.
Set clock
1
Press MENU/DISP for 3 seconds.
2
Press 3 or 4 repeatedly to until the cur-
rently time is displayed.
3
Turn z clockwise to set hour.
4
Press z to confi rm.
5
Turn z anti-clockwise to set minute.
6
Press z to confi rm.
View clock
1
Press MENU/DISP repeatedly until the clock
is displayed.
Listen to radio
1
Press SOURCE repeatedly to select Tuner.
2
Press or to select band: [FM1], [FM2],
[FM3], [AM1], or [AM2] .
3
Press ∞ or § to tune to a radio station
manually.
• To search for a radio station
automatically, press SEARCH for 3
seconds.

Pairing bluetooth devices

You can pair your bluetooth device with the unit
as follows:
1
Turn on bluetooth function on the device.
2
Setup bluetooth fuction on your device.
3
Select "CEM250" in the pairing list.
4
Enter default password "0000".
» " [CONNECT] " is displayed on the
panel if pairing succeeds.
5
Press and hold SOURCE to disconnect
Bluetooth connection.