Philips CEM250/98 Quick Start Manual

Register your product and get support at
EN Quick Start Guide
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
Document order number: CEM250_98_QSG_V2.0
CEM250
1
a b c
e f g
2
3 4
B
Overview of parts 1
5 REAR LINE
OUT L
These are the supplied parts needed to
6 SUB OUT
connect and install this unit.
7 ANTENNA Antenna
1 In-car audio system
2 Sleeve
3 Front panel
For cars with ISO connectors
4 Standard connector
5 Trim plate (1 pieces)
6 Rubber cushion
Caution
7 Disassembly tools
8 Screws 4 pieces • Be sure to connect the black ground (earth)
lead fi rst.
1
Connect wires Connect the antenna and amplifi er as
illustrated, if applicable.
2
Cut off the bigger end of the supplied stan-
dard connector.
Caution
3
Check the car's wiring carefully and connect
• Ensure that all loose leads are insulated with
them to the supplied standard connector.
electrical tape.
4
Connect the supplied standard connector to
the unit.
For cars with ISO connectors 2 3
1
Pull out the ISO connectors from car
1
dashboard and connect them to the bigger
end of the supplied standard connector.
2
2
Connect the other end of the supplied
standard connector to the unit.
3
3
Connect the antenna and amplifi er as
illustrated, if applicable.
4
Connector Connect to
1 MIC Microphone
2 FRONT Front right speaker
e RED
LINE OUT
R
f BLUE
3 FRONT Front left speaker
LINE OUT
L
4 REAR LINE Rear right speaker
g BLACK
OUT R
5
d
h
a
a a
b
c
d
a
b b
b
c
d
e c
c
f
g
h
i
d
d
Rear left speaker h Orange/ Illumination switch
white
Subwoofer i YELLOW To the +12V car battery
which is energized at all
times
3 4
Note
Check wire connection before you mount
•
the unit into a car.
• If preset radio stations are lost when the
ignition key is turned OFF and then back
ON, reconnect the red leads crosswise to
the yellow ones.
Mount in the dashboard 5
1
If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
Green/black Left speaker • If you disconnect the car battery in a car
that has an on-board drive or navigation
strip (Rear)
computer, the computer may lose its
White/black Left speaker
memory.
strip (Front) • If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
Gray/black Right speaker
wires do not touch each other.
strip (Front)
2
Remove the two screws on the top of the
Purple/black Right speaker
unit.
strip (Rear)
3
Remove the mounting sleeve with the
supplied disassembly tools.
Ignition key +12V DC 4
Install the sleeve into the dashboard and
bend the tabs outward to fi x the sleeve.
when ON/ACC
5
Place the rubber cushion over the end of
Motor/electric antenna
the bolt.
relay control lead/
6
Slide the unit into the dashboard until you
Amplifi er relay control
hear a click sound.
lead
7
Reconnect the negative terminal of the car
Ground
battery.
Attach the front panel 5 Pairing bluetooth devices
1
Attach the trim plate.
You can pair your bluetooth device with the unit
2
Insert the right side of the panel in the
as follows:
chassis until it is correctly engaged.
1
Turn on bluetooth function on the device.
3
2
Press the left side of the panel and point
Setup bluetooth fuction on your device.
the left hole at the left pillar.
3
Select "CEM250" in the pairing list.
4
Release the panel to engage the left side. 4
Enter default password "0000".
» " [CONNECT] " is displayed on the
panel if pairing succeeds.
5
Turn on
Press and hold SOURCE to disconnect
Bluetooth connection.
1
Press z to turn on the unit.
• To turn off the unit, press z for 3
Note
seconds.
ou can hold SOURCE again to reconnect
• Y
last used Bluetooth device.
Set clock
1
Press MENU/DISP for 3 seconds.
2
Press 3 or 4 repeatedly to until the cur-
Make a call
rently time is displayed.
3
Turn z clockwise to set hour.
1
Press SOURCE repeatedly to select BT
4
Press z to confi rm.
MUSIC.
5
2
Turn z anti-clockwise to set minute.
Press .
3
6
Press z to confi rm. Press or to select from the following
list:
DIAL NUM
• : dial number directly
View clock
• DIALLED : dialed number
• MISSED : missed call
1
Press MENU/DISP repeatedly until the clock
• RECEIVED : received call
is displayed.
ME PBK
• : Phone directory
• SIM PBK : SIM directory
Listen to radio 4
Press to confi rm the selection.
1
Press SOURCE repeatedly to select Tuner.
To dial a number directly, select DIAL NUM.
2
Press or to select band: [FM1], [FM2],
1
Press 0-9 to enter phone number.
[FM3], [AM1], or [AM2] .
• Press / to change a number.
3
Press ∞ or § to tune to a radio station
• Press to reset entered numbers.
manually. 2
Press to dial.
• To search for a radio station
To use a number in call log or directory, select the
automatically, press SEARCH for 3
option other than DIAL NUM.
seconds.
1
Turn to select a number from call log or
directory.
2
Press to dial.