Fault In Water Flow; Technical Specifications; Removing The Appliance - Thermador TCM24PS Installation Instructions Manual

13 Check that the appliance is in the middle. If necessary,
align the appliance. To do so, pull the appliance out a little,
remove the appropriate spacers e and attach to the left
side (top and bottom). Push the appliance into the unit until
it clicks into place. Align the appliance horizontally and
vertically. The appliance must not stand at an angle of more
than 1° (2 %) in any direction!
14 Take hold of the appliance door on the right next to the
outlet and open. Remove the drip tray Y. Pull the cover X on
the bottom left-hand side forwards and remove. Pull out the
accessories drawer Z and put to one side.
15 First, screw on the appliance as shown using 2 of each
of the fastening screws f and g as well as 2 sleeves j.
Then screw tight at the top right of the unit using 1 fastening
screw f and sleeve h.
16 Only for the qualified installer
In very few cases, the door of the built-in fully automatic
machine can jam due to a misalignment in the built-in unit.
The door can be adjusted. To do this adjust the hinges at the
top and the bottom.
I. Adjust the depth of the door by turning the screws V.
II. Remove the hinge dampers at the top and bottom of the
hinges. Turn the screws W to adjust the inclination and
the horizontal position of the doors.
III. Re-fit the hinge dampers.
17 Insert the cover X and fix with the two black fastening
screws i.
18 Replace the drip tray Y and accessories drawer Z and close
the appliance door.

Fault in water flow

To ensure an adequate water flow, the filter in the AquaStop
should be cleaned regularly. Turn off the tap. Unscrew the water
inlet hose with the AquaStop from the tap. Clean the filter with
a small brush.
Important: Do not remove the filter under any circumstances.
Screw the water inlet hose with the AquaStop to the tap. Slowly
turn on the tap so it is fully open. Check the connections and
water inlet hose for leaks. If the appliance is cleaned and main-
tained regularly, this will avoid faults.

Removing the appliance

● Run emptying program. See instruction manual.
● Turn off the tap.
● Disconnect the mains plug.
● Remove the water inlet and water outlet hoses.
● Remove all screws. See installation.
● Gently pull out appliance.
● Pull the appliance out from the cabinet.
4 – en

Technical specifications

Power connection
with transformer type 8001010566
(voltage – frequency)
Power rating
Maximum static pump pressure
Maximum water tank capacity
(without filter)
Maximum capacity of the
coffee bean container
Length of power cable
(Power socket – transformer)
Dimensions
(appliance without transformer)
H x B x D
Weight, empty
(appliance without transformer)
Dimensions (only transformer)
H x B x D
Weight (only transformer)
Type of grinding unit
AQUA-STOP pledge
In addition to the standard warranty provided by BSH, BSH will
also compensate customers for damage caused by a specific
fault in the AquaStop system giving rise to a valid warranty
claim. Compensation will be provided under the following
conditions:
1. If water damage is caused by a defect in materials or
workmanship in the AquaStop system, BSH will compensate
customers reasonable and verifiable damages.
2. A condition of all warranty claims is the appliance with
AquaStop must have been installed and connected correctly
in accordance with all instructions; this also includes a prop-
erly installed AquaStop extension (genuine accessories).
The warranty does not cover defective feed lines or fittings
leading to the AquaStop connection at the tap.
120 V AC – 60 Hz
1600 W
19 bar
81.15 oz (2.4 l)
1 lb (500 g)
39" (1 m)
17 7/8" x 23 3/8" x 14 3/4"
(455 x 594 x 375 mm)
42-44 lb (19-20 kg)
8 1/4" x 6 3/4" x 7 13/16"
(210 x 172 x 198 mm)
27.55 lb (12.5 kg)
Ceramic