Whirlpool W10661461B Instructions

DOOR SWING AND HANDLE REVERSAL INSTRUCTIONS W10661461B (OPTIONAL)
Remove food and any adjustable bins from the doors.
IMPORTANT: Unplug refrigerator or disconnect power. Provide additional support for the doors while the hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.
When removing the door, keep the screws and hinges. You will need them to reinstall the door. For more detailed door reversing instructions, see the User Instructions.
While holding the door,
Remove Freezer
remove 3 hex head
and Refrigerator screws and the hinge pin.
Doors
NOTE: After removing the
doors, place them on a soft
surface to avoid damaging
the finish. 1
Move the door stop, located on the bottom of the door,
to the opposite side.
Freezer
Door
1
A. Door Stop Screw B. Door Stop
Move the door stop, located on the bottom of the door,
to the opposite side.
Refrigerator
Door
1
A. Door Stop Screw B. Door Stop
Move the bottom hinge to the opposite side
of the cabinet. Make sure the washer remains
on the hinge pin. NOTE: The hinge style
will vary depending on the model.
Refrigerator
Door
or
1
Move the 3 cabinet hole
plugs to the opposite side.
Freezer
Door
1
Align the Freezer and Refrigerator
doors. NOTE: Make sure to allow a
¾" (19 mm) gap between the doors.
Align
Doors
(19 mm)
1
W10661461B
© 2014 Whirlpool Corporation.
All rights reserved.
Center Hinge - Loosen the 2
Lift freezer door from
screws (6 turns) on the left-
the center hinge pin.
hand side and remove the
screw from the right-hand side.
2 3
Remove the handle and brand
badge from the door.
NOTE: Handles are not factory-installed
on some models.
A
B
2
Remove the door handle, the screw
and the decal or hole plug from the door.
A
B
2
Set the Refrigerator door onto
the bottom hinge pin.
2
Insert the 3 Top Hinge screws
Set the freezer door
so they are halfway into the
onto the Center Hinge.
Top Hinge and the top of
the cabinet.
2 3
Completely tighten the Move the base grille cover
4 Top Hinge screws. to the opposite side.
¾"
2 3
For models with base grilles, Center Hinge - While holding the
door, loosen the 2 screws on the
firmly pull the grille
right-hand side and remove the
toward you to remove.
screw from the left-hand side.
4 5
Place the badge (using the template provided
on the last page of the manual), and the
handle on the opposite sides of the door.
3
Move the decal or hole plug and the handle
screw to the opposite sides of the door.
3
Tighten the screws (previously loosened),
and reinstall and tighten the Center Hinge screw.
NOTE: Make sure washers are on both the top
and bottom pins of the center hinge.
3
Tighten the two screws (previously
Reinstall the base grille.
loosened), and reinstall and
tighten the Center Hinge screw.
4 5
www.goedekers.com
Use two or more people to move and install
refrigerator.
Lift refrigerator door from bottom
Failure to do so can result in back or other injury.
hinge. NOTE: The hinge style will
vary depending on the model.
or
6
Tighten the handle
Open doors left to right.
screws.
4
Tighten the handle
screws.
4

WARNING

Excessive Weight Hazard
Open doors right to left.

Tools Required

5 16 " Hex head socket wrench
5 16 " Open-end wrench
Phillips screwdriver
1 8 ¼" Hex key
Flat 2" putty knife

Reversibility Kit

(a) Removal tool Brand
(a) (b)
Badge
(b) Brand badge
(d)
(c) Instructions
(c)
(d) Hole plug
(e)
(e) Two screws
6/14
Printed in Mexico