English Table of Contents Interesting information on collagen .................3 Important notes on the use of collagen ..............5 Collagen exposure program ...................5 Exposure distance .....................5 After exposure ....................5 System Installation ....................6 1. Baseplate ......................6 2. Right element ....................6 3. Left element ....................7 4.
Dear customer, With the purchase of a DR. KERN collagen/ tanning combination unit, you have selected high quality technology and a high-perfor- mance unit. During production of this unit, we have taken all measures possible to guaran- tee fault-free, safe operations. Furthermore, you can make a significant contribution to ensuring that you are satisfi...
Page 4
If the power supply cable has to be exchanged or reattached, the type stated in the technical data must be used. • This unit is not intended for use by persons (including children) with re- stricted physical, sensory or mental capacity or by persons without the ne- cessary experience and/or knowledge Air intake slits or hot air ventilati-...
Important notes on the use of col- Collagen exposure program lagen • Photosensitive persons (e.g. LE or MCS) should consult a physician before use. • Please note: certain medication can infl u- Read the instructions carefully. ence the body's general reaction to light. Please consult your physician in case of any doubt.
System Installation 1. Baseplate Begin the assembly by removing the base- The system is delivered in several separa- plate (D) from package 4, and placing it at tely packed sections for transport to its fi nal the intended location of the system. installation point.
Stand foot, facing side lower left: 4. Installing the elements preassem- bled in steps 2 and 3 From the accessory pack, take the stand foot (7), two M10 nuts (5) and washers (6), Installation of the right element and assemble the foot as shown in Fig. 4. Lift the element and place it in the tongues provided (13 + 1) in the baseplate (Figs.
Now lift the stand foot (8) on the lower left The two elements are now assembled. side into the positioning tongue (14) in the Note: Check the correct position in baseplate (Fig. 9). relation to the baseplate and the ali- gned position! Fig.
Note: The operating panel (17) must not 6. Installing the door element be bolted to the lower plate yet! Remove the door element (C) from package Now place the attachment holes in the ex- Note: The retaining bolt (21) for the haust unit over the matching holes in the castor, and the upper and lower bea- tanning elements.
Now let the installation plate (24) drop down 8. Installing the upper trim panels over the upper bearing, and tighten the two Finally, fi t the three trim panels (33) around nuts (26) fi rmly (Fig. 18). the upper edge of the system (Fig. 20), using for each panel two self-tapping screws (34) on the outside, and two M4 screws in the central area.
Page 11
Fig. 21 Fig. 22 Fig. 23 Connect the main power cable to the mains power source using a fi xed connection or a plug connection (CECON plug). The system is now ready for operation.
Operation Timer adjustment The unit will be switched on by using the On/ Off- switch (1) at the digital-timer. With the keys (4) and (5) (fi g. 24) you can select your tanning time (max. 30 minutes). (5) = up, (4) = down With the key (3) the body fans are switched on or off.
Maintenance Cleaning the collagenshower and the Replacing tubes and starters acrylic plates To replace tubes and starters, fi rst remove the acrylic plates as described above. Use a moist cloth to clean the collagensho- wer. The acrylic plates should also be clea- The tubes in your tanning system must be ned at regular intervals.
Hose output diameter should not be reduced at any point in the exhaust line, as this may result in air blockage. Technical data Type Skinfresh Tancan 3000 Collagen lamps 30 x 100 W Length of lamps 1,76 m Power rating, app.
Switching to coin box operation Returning to timer operation 2 persons are required for this procedure. Returning the sun bed back to timer operati- on is only possible if the coin box is comple- • When the coin box is not connected yet, tely disconnected and the jumper “L1-Time”...
Guarantee The guarantee is taken over according to the le- gal regulations at present. Manufacturer’s warrenty - The period of warranty starts from the date of purchase and is in principle valid for 12 months. - Always include the completed warrenty certifi- cate when returning equipment.
Handling procedures for return shipments (RMA) - Details for all returns ! Dear customer we hope that you will rejoice in the ordered articles. Just in case that you are not entirely contented as an exeption, please follow the procedures specified below.This enabling us to ensure a quick and smooth handling of the return shipment.
Need help?
Do you have a question about the Skinfresh Tancan 3000 and is the answer not in the manual?
Questions and answers