Advertisement
5.0 - ANTI-HIJACK FEATURE
Arming the anti-hijack feature means that only TAG reception and identification is
activated and not vehicle immobilization.
The 972AR module has an anti-hijack feature for protection against aggression or vehicle theft.
It operates by means of an automatic transmitter (TAG), which comunicates with the 972AR module
via a codified radio signal.
When ignition is turned OFF, the module arms and works as an alarm and the TAG as a remote control.
When the vehicle is running and there is no TAG transmission,
hijack procedure,
as described further on
For security reasons, we recommend you keep your electronic key and TAG separate
from your ignition key so that, if your vehicle is robbed, you have your electronic key
This feature can be activated even if the vehicle is turned OFF;
not detect the TAG, the anti-hijack feature arms
5.1 - VEHICLE
Under this condition, the system only detects
5.2 - VEHICLE RUNNING: AGGRESSION AND HIJACKING
As already mentioned, in case of car theft, the user should still have his TAG with him.
opened and the driver walks away with theTAG, the module no longer detects radio contact and
.
enters, after 60", in pre-arm mode
5.3 - VEHICLE RUNNING: ANTI-HIJACK ACTIVATION
The turn indicators and the buzzer, siren or the horn (if connected) will activate for 2 minutes
20" after the audio/visual signals, the vehicle immobilizer will activate (20" ON/OFF up to a complete
stop)
.
If the driver doesn't turn them off, the turn indicators will keep flashing for 3 hours while the siren or
horn will sound for two minutes
.
5.4 - DEACTIVATION OF ANTI-HIJACK FEATURE
To deactivate the anti-hijack feature all the driver has to do is walk up to his vehicle with the TAG.
The module, on intercepting the signal, will deactivate the anti-hijack feature and stop the optic and
acousic alarm signals.
Deactivation of the anti-hijack feature with electronic key will arm the "garage function" (see par. 4.0).
PAGE 04 - USER MANUAL
the alarm system activates the anti-
.
and TAG with you.
if it is turned ON and the system does
.
RUNNING
: NORMAL OPERATION
TAG transmission and the LED does not blink
6.0 - TAG CARD ACTIVATION AND BATTERY REPLACEMENT
To activate the TAG CARD simply press the button and keep it pressed for at least 4 seconds.
The LED turns on steady when the TAG is activated and it will flash each time the TAG transmits.
If not moved for 10 min., the TAG will automatically go into standby to save battery life; to' wake it up' for
another transmission cycle (10 min.), move it or press the button
Another short button press will send a radio signal to the alarm system.
To turn the TAG off, press the button and keep it pressed for at least 8 seconds.
The LED stays on steady and after 8 seconds it will flash briefly to indicate the TAG is switched off.
To replace battery proceed as follows
Separate the plastic
covers and remove the
circuit with care.
.
Figure 1
If the door is
.
Use ONLY CR2032 type battery; do not discard used batteries in trash but safely
This product is garanteed to be free from defects in workmanship for a period of 24 months from the
date of installation reported on this warranty, in compliance with the 1999/44/CE Warranty Directive
(L.D. N° 24 of the 02/02/2002).
Please fill-in entirely the guarantee certificate included in this booklet and DO NOT REMOVE the
guarantee label from the device.
The warranty will become void if labels are misssing or torn, if the installation certificate is not fully
compiled or if the enclosed sale document is missing.
The warranty is valid exclusively at Authorized Gemini Centers.
The manufactuer declines any responsability for eventual malfunctions of the device or any damage
to the vehicle electrical system due to improper installation, use or tampering.
This alarm is solely intended to be a theft-deterrent device.
:
Reassemble the covers, turn
on the TAG and make sure it
works.
Figure 3
dispose in appropriate containers.
7.0 - WARRANTY CONDITIONS
.
Slide out dead battery
and insert new one.
Pay attention not to
invert polarity.
+
Figure 2
USER MANUAL - PAGE 05
Advertisement
