Advertisement
JSTT1000
1000-LBS.
CAPACITY
TRANSMISSION JACK - 2 STAGE
OWNER'S MANUAL
SPECIFICATIONS
Maximum Capacity ........................................................ 1000-Lbs.
Minimum Height ................................................................ 35-1/2"
Maximum Height ...................................................................... 74"
Saddle Tilt Fore and Aft ................................................ 37° by 26°
ASME PASE-2014
Saddle Tilt Side to Side ................................................ +12°, -12°
Base Size ................................................................30-1/4" square
Weight ............................................................................. 143-Lbs.
© 2015 Mac Tools
JSTT1000
6/3/15
Advertisement
Table of Contents
Related Manuals for MAC TOOLS JSTT1000
Summary of Contents for MAC TOOLS JSTT1000
- Page 1 Minimum Height ..............35-1/2" Maximum Height ..............74" Saddle Tilt Fore and Aft ..........37° by 26° ASME PASE-2014 Saddle Tilt Side to Side ..........+12°, -12° Base Size ..............30-1/4" square Weight ................143-Lbs. © 2015 Mac Tools JSTT1000 6/3/15...
-
Page 2: Warning Information
It is the responsibility of the owner to make sure all personnel read this manual prior to using this jack. It is also the responsibility of the jack owner to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost or not legible, contact Mac Tools for replacements. If the operator is not fluent in English, the product and safety instructions shall be read to and discussed with the operator in the operator's native language by the purchaser/owner or his designee, making sure that the operator comprehends its contents. -
Page 3: Setup Instructions
JSTT1000 1000-LBS. CAPACITY TRANSMISSION JACK - 2 STAGE SETUP INSTRUCTIONS WARNING Failure to follow these Setup Instructions may result in serious injury or death, and/or property damage. 1. Place the hydraulic power unit in an upright position. Secure the legs (#2-5) to the cylinder (#1-1) with the bolts (#2-3) and washers (#2-4). Do not tighten. 2. Secure swivel casters (#2-1 and #2-2) to leg caster brackets as shown in the exploded view drawing on page 5. 3. Tighten the hardware that secures the legs (#2-5) to the cylinder (#1-1). 4. Place the saddle assembly (RS1000SA) on the stud protruding from the top of the hydraulic unit assembly. Align the hole in the saddle with the hole in the stud, and secure with the bolt (#3-26) and nut (#3-27). 5. The hydraulic power unit is equipped with two reservoir fill screws (#1-37 and #1-38). The closed filler screw is installed in the reservoir at the factory so the jack will not leak during shipment. -
Page 4: Preventative Maintenance
Purge air from hydraulic system as above. 4. Handle tends to raise up while the unit is under rated load. Pump the handle rapidly several times to push oil past ball valves in power unit. 5. Unit still does not operate. Contact your Mac Tools Distributor. JSTT1000 6/3/15... -
Page 5: Parts Diagram
JSTT1000 1000-LBS. CAPACITY TRANSMISSION JACK - 2 STAGE PARTS DIAgRAM RS1000HUA Complete Replacement RS1000SA Hydraulic Unit Assembly Complete Saddle Assembly 3-5A 3-5B 1-55 3-5C 1-62 1-54A 1-61A 3-24 3-25 3-23 1-63 1-60 1-53A 1-59 1-52 3-16 3-15 3-17 1-58 1-51... -
Page 6: Parts List
JSTT1000 1000-LBS. CAPACITY TRANSMISSION JACK - 2 STAGE PARTS LIST Index No. Part No. Description Qty. Index No. Part No. Description Qty. 1-40 Nut Oil Cylinder Assembly 1-41 Bolt Steel Ball Ball Seat 1-42 Handle Sleeve 1-43 Draw Bar Spring... -
Page 7: Limited Warranty
This warranty does not cover damage to equipment or tools arising from alteration, abuse, misuse, damage and does not cover any repairs or replacement made by anyone other than Mac Tools. The foregoing obligation is Mac Tools sole liability under this or any implied warranty and under no circumstances shall we be liable for any incidental or consequential damages.