Advertisement
SLEEP
(See 6)
About Sleep
This set has a built-in sleep timer, which enables the radio to be automatically
switched off after a set period of time. There are four sleep time options.
Setting and switching off SLEEP
1
Within 1 second, press ALARM RESET / SLEEP twice until the display shows
SLEEP and SL: 60.
™
The radio is automatically switched on and tunes to the last station.
2
To select other sleep time options, press ALARM RESET / SLEEP again within 1
second before the display returns to clock time.
™ The display shows in sequence:
3 To cancel sleep, press either:
–
RADIO ON/OFF
– REPEAT ALARM /
BRIGHTNESS CONTROL
–
ALARM RESET / SLEEP
once or more until
display.
USING THE PROJECTION
You may have the experience of looking for a clock in the darkness. With this
projection feature, you can conveniently project the clock time onto a surface
e.g. walls ceiling (furniture, glasses not recommended).
1
Press
PROJECTION ON/OFF
to switch on.
™
The Projection lens lights up red.
2
Turn the Projection lens wheel (maximum 180 degree left or right) and also the
set, if necessary, to find a suitable projection surface.
3
To change the projected time upside down, press REVERSE PROJECTION.
4.
To change the projection slightly to a different angle, turn the ROTATE PROJEC-
TION ball (maximum 75 degree left or right.).
5.
Press
PROJECTION ON/OFF
to switch off.
™
The Projection lens goes out.
TROUBLESHOOTING
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or
service centre.
WARNING: Under no circumstances should you try to repair the set yourself, as this
will invalidate the guarantee. Do not open the set as there is a risk of
electric shock!
No sound
– Volume not adjusted
• Adjust the volume
No display backlight / display malfunction/ radio and alarm do not
function
– Set is in Power Low mode
• Connect AC/DC adapter or insert fresh batteries
Display error / no reaction to any controls
– Electrostatic discharge
• Press the RESET hole on the bottom of the set with a ball-pen. Or disconnect
set from AC/DC adaptor and batteries for 5 minutes, then re-plug.
Continuous crackling and hiss noise during
– Interference from other electrical equipment e.g. TVs, computers, fluorescent
lamps
• Move the clock radio away from electrical equipment
Intermittent crackling sound during FM reception
– Weak signal
• Extend and position the pigtail aerial
SL : 30, SL : 15 and OFF.
.
SLEEP
disappears from the
(See 7)
MW
reception
Helpful hints:
– When battery-powered, the projection lens lights up briefly to help save energy.
– To a longer projection time, please use the supplied 7.5V AC adapter to oper
ate the set.
MAINTENANCE & SAFETY
• If you do not intend to use set for a long time, remove the batteries.
• Do not expose the set to humidity, rain, sand or excessive heat caused by
heating equipment or direct sunlight.
• To clean your set, use a soft damp cloth or chamois leather. Do not use clean-
ing products, which contain benzene, thinner, etc. as these may harm the
housing.
ENVIROMENTAL INFORMATION
We have reduced the packaging to its minimum using only paper and cardboard.
Your set consists of materials which can be recycled if disassembled by a
specialized company. Please observe local regulations on the disposal of
packing materials and old equipment.
The alarm does not function
– Alarm time/ mode not set
• See SETTING THE ALARM
– Volume too low for radio
• Increase the volume
– AL 1 (AL
)
not tuned to a radio station
•
Check if the set is tuned to a radio station before you set
switch off the radio.
Blurry projection
– Distance/ angle between the projection surface too large
• Reduce the distance/ angle.
This product complies with the radio interference requirements of the
European Union.
The typeplate and production number are located inside the battery
compartment.
AL1
and when you
Advertisement
