Table of Contents
Advertisement
INSTRUCTION MANUAL
20V MAX LI-ION
CORDLESS HAMMER DRILL/DRIVER KIT
TDHD02P
Operation /Safety Instruction
TECCPO is committed to providing the best After-sale Service,we strive for your FIVE STAR satisfaction!
support@teccpo.net / support@teccpotools.com
TDHD02P
20V Max
Advertisement
Table of Contents
Summary of Contents for Teccpo TDHD02P
- Page 1 INSTRUCTION MANUAL 20V MAX LI-ION CORDLESS HAMMER DRILL/DRIVER KIT TDHD02P Operation /Safety Instruction TDHD02P 20V Max TECCPO is committed to providing the best After-sale Service,we strive for your FIVE STAR satisfaction! support@teccpo.net / support@teccpotools.com...
- Page 3 Original Instructions Description of Symbols The rating plate on your tool may show symbols.These represent important information about the product or instructions on its use. Wear hearing protection Wear eye protection Wear breathing protection Wear head protection Wear hand protection Read instruction manual DO NOT incinerate batteries! Caution!
- Page 4 Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice. Li-Ion Conforms to relevant legislation and safety standards. Li-ion battery cells are recyclable and should not be disposed of with household waste.
- Page 5 Product Features TDHD02P 20V Max 1. Chuck 2. Torque Selector 3. Mode Selector 4. Gear Switch 5. Motor Vents 6. Forward/Reverse Switch ACCESSORY 7. Trigger Switch 2.0Ahr Li-ion Battery Pack 2pcs 8. Soft Grip Handle Fast Charger 9. Working Light...
- Page 6 necessary, limit the length of time exposed to vibration and use anti-vibration gloves. Do not operate the tool with hands below a normal comfortable temperature, as vibration will have a greater effect. Use the figures provided in the specification relating to vibration to calculate the duration and frequency of operating the tool.
- Page 7 protected supply. Use of an RCD reduces the risk of electric shock. 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
- Page 8 supplied via Residual Current Device (RCD) with a rated residual current of 30mA or less. 5) Battery tool use and care a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. b) Use power tools only with specifically designated battery packs.
- Page 9 l) If you are interrupted when operating the drill, complete the process and switch off before looking up. m) Where possible, use clamps or a vice to hold your work. n) Examine the chuck regularly for signs of wear or damage. Have damaged parts repaired by a qualified service centrer) ALWAYS wait until the drill has com.
- Page 10 Before Use Removing a battery Remove the Battery from the tool by pressing the Battery Release, then slide the Battery out of the Battery Slot. WARNING: DO NOT try to remove the Battery without pressing the Battery Release button. The tool or Battery could be damaged.
- Page 11 2. Once charging commences, the Red LED will on. 3. When the Battery is fully charged, the Red LED will off and Green LED will on. Battery Charge Level: The Battery has a built-in Battery Charge Indicator Pressing on the button to the right will indicate the charge level. The right LED indicates a high charge level and the left a low charge level that will mean the battery pack will require charging soon.
- Page 12 Machine to test that it is running centrally, smoothly and evenly. If the bit is 'wobbling' or not running centrally, release the chuck, check the accessory for damage,correct its position, retighten and test again. Operation Direction control WARNING: NEVER change the direction of rotation while the tool is running. This may cause permanent damage to the tool.
- Page 13 Screwdriver use Note: Always use a universal bit holder when working with screwdriver bits. Do not mount screwdriver bits directly into the chuck. 1. Select gear 1 using the Gear Switch (4). 2. Rotate the Mode Selector (3) to Drive. 3.
- Page 14 - Use a countersink bit to remove sharp burrs from the hole, preventing cuts and other kinds of injury. WARNING: If the power tool gets excessively hot in use, stop using the tool immediately and allow to cool before continuing work. The cooling period can be reduced by operating the drill at maximum speed with no load.
- Page 16 Shenzhen Allsight E-business Co., Ltd Web:www.teccpotools.com Facebook:www.facebook.com/Teccpo.US E-mail：support@teccpotools.com ADD:Room 104, Building P09, south China City Electronic trading Center, Longgang District, Shen Zhen, CHINA Made in China...