Sealey 800TTJ Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMpORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS &
CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE
1. SAFETY INSTRUCTIONS
WARNING: The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions

and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
WARNING! Ensure all preliminary checks are carefully carried out before use of jack. Immediately repair or replace damaged

parts (use authorised service agent). Ensure use of genuine parts only. Unauthorised parts may be dangerous and will invalidate
the warranty.
WARNING! Use jack on level and solid ground, preferably concrete. Ensure the floor over which the jack will be transported is swept

clean.
DANGER! DO NOT use on tarmacadam, or any other soft surface as jack may sink or topple. Serious injury may result if ignored.

DANGER! If jack tips or leans STOp WhAT yOUR ARE DOING. MOVE QUICKLy TO A SAFE DISTANCE. DO NOT TRy TO hOLD

OR STEADy JACK.
Use jack in a suitable work area. Keep the area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.

Before use ensure the gearbox weight and size does not exceed the capacity of the jack.

Ensure the vehicle is raised and stabilised at the correct height before attempting to move the jack

under the vehicle.
Ensure the jack saddle is fully lowered and is clean, dry, and oil free before attempting to

transport the jack with or without a load.
Keep all unauthorised persons away from the jack during lifting and lowering and when in transit.

Maintain correct balance and footing. Ensure the floor is not slippery and wear non slipshoes.

Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery,

and contain/tie back long hair.
WARNING! Ensure that the load is placed level and centrally on the jack saddle and that

it is fixed in place before attempting to lift, lower or transport the load.
The lowering speed will vary according to the weight of the load and the release valve setting.

Diligence is required in ensuring that you continually monitor the operation until completed.

Should the jack make any abnormal sounds during use, STOP IMMEDIATELY and contact

your local service agent.
DO NOT operate the jack if any parts are damaged or missing.

DO NOT exceed the rated capacity of the jack.

DO NOT raise/lower vehicle lifting platform whilst the transmission jack is being used.

DO NOT transport the jack with/without a load, with the saddle in the raised position.

DO NOT get the jack wet, or use it in damp or wet locations or areas where there is condensation.

DO NOT operate the jack when you are tired or under the influence of alcohol, drugs or intoxicating

medication.
DO NOT lift or support vehicles with the jack and do not use the jack as a load sustaining device.

DO NOT use the jack for any purpose other than removal, transportation and the installation of

transmissions.
DO NOT make any modifications to the jack.

DO NOT adjust, or tamper with, the safety valve.

DO NOT remove any labels from the jack. If the labels are damaged or unclear, replace them.

DO NOT use brake fluid to top up the hydraulic unit.

Use Sealey hydraulic oil only.

Use a qualified person to to lubricate and maintain the jack.

Before storing the jack in a safe area, ensure that all parts are clean and free of

grease and oil, especially the saddle.
2. SPECIFICATION
capacity . . . . . . . . . . . . . . . . . . . . . . . . .800kg
Ram Extensions . . . . . . . . . . . . . . . . . . . . . . . .2
Minimum Saddle Height . . . . . . . . . . . . .960mm
Maximum Saddle Height . . . . . . . . . . .1920mm
Base Size . . . . . . . . . . . . . . . . .1046 x 1046mm
fixed/Adjustable Saddle. . . . . . . . . . Adjustable
Saddle Tilt - forward: . . . . . . . . . . . . . . . . . . 15°
Saddle Tilt - Backward: . . . . . . . . . . . . . . . . 40°
Saddle Tilt - Side to Side . . . . . . . . . . . . 15-40°
Telescopic 2-stage model for reduced clearance lifts. foot pedal operation keeps hands free. Spring-loaded dead man's safety release control
reduces the risk of inadvertent lowering. Highly manoeuvrable on castors.
© Jack Sealey Ltd
InSTRUcTIonS foR:
TRANSMISSION JACK 0.8 TONNE TELESCOPIC
800TTJ
MoDEL no:
Original Language Version
800TTJ Issue: 1 - 22/02/13