Advertisement
Quick Links
Battery Replacement Kit
Greensmaster
Model No. 04069
Model No. 04070
Safety
Safety and Instructional
Decals
Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.
1. Warning—read the
Operator's Manual.
2. Warning—keep at
temperatures below 65° C
(149° F).
1. Warning—read the Operator's Manual before performing
maintenance.
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
eFlex
137-9712
3. Explosion hazard—do not
open the battery; do not
use a damaged battery.
4. Warning—read the
Operator's Manual
for battery charging
information.
139-5614
Register at www.Toro.com.
®
Series Traction Unit
Battery Decal
The battery manufacturer provides the following
language that corresponds to decal 137-9712:
1.
Do not expose battery to temperature above
65°C (149°F).
2.
Do not disassemble or mistreat battery. Do not
crush.
decal137-9712
3.
Do not drop or subject it to impact.
4.
Use only OEM approved charger.
5.
Failure to follow those instructions may present
risk of explosion, fire or high temperatures.
6.
See owner's manual for additional safety
instructions.
decal139-5614
Form No. 3431-643 Rev A
Installation Instructions
137-9712
Original Instructions (EN)
All Rights Reserved *3431-643* A
Printed in the USA
g286686
Advertisement
Summary of Contents for Toro 04069
- Page 1 Form No. 3431-643 Rev A Battery Replacement Kit Greensmaster ® eFlex ® Series Traction Unit Model No. 04069 Model No. 04070 Installation Instructions Safety Battery Decal The battery manufacturer provides the following Safety and Instructional language that corresponds to decal 137-9712:...
-
Page 2: Installation
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. – No parts required Remove the existing battery. Battery pack Bolt (1/4 x 4-1/2 inches) Washer (1/4 inch) Install the battery to the battery platform. - Page 3 Remove the tall nut that secures the rear of the battery platform to the machine frame (Figure Removing the Existing Battery No Parts Required Procedure Note: You may discard all removed parts unless g017238 Figure 3 otherwise noted. 1. Tall nut Remove the 4 bolts that secure the console cover and remove it (Figure...
- Page 4 Remove the 2 nuts, washers, and bolts securing the power center bracket to the rear of the machine and remove it (Figure Installing the Battery to the Battery Platform Parts needed for this procedure: Battery pack Bolt (1/4 x 4-1/2 inches) Washer (1/4 inch) Nut (1/4 inch) Lock washer (M8)
- Page 5 Loosen the 8 screws securing the battery cover Connect the controller cable to the connector at and remove it (Figure the top of the battery (Figure Connect the positive (red) cable to the positive Note: You do not need to completely remove (+) battery terminal and secure it with a lock the screws to remove the cover.
- Page 6 Installing the Battery Platform and Wire Harness Assembly Parts needed for this procedure: Battery, platform, and wire harness assembly g272547 Bolt (5/16 x 1 inch) Figure 11 Spacer (5/16 inch) 1. Nut (5/16 inch) 3. Bolt (5/16 x 2-1/4 inches) Nut (5/16 inch) 2.
-
Page 7: Completing The Installation
Note: The battery is shipped with a partial charge (approximately 30%); this is enough Use Toro DIAG to update the software to charge for you to perform software installation, the latest available; refer to your Toro DIAG function checks on machine, and move it as Operator’s Manual. - Page 8 Warranty coverage—Tier 1: Full warranty coverage applies to the first 2 years (730 days) from product purchase invoice date or 820 kWh of battery output, whichever occurs first. If a warrantable failure occurs during tier 1, Toro will replace the battery with a new battery at no charge to you. This includes diagnostics, labor, parts, and transportation.