Advertisement
Quick Links
Trimmer Mount Kit
Titan
Model No. 136-1682
This product contains a chemical or chemicals known to the State of California to
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Description
No parts required
Rear bracket
Nut (1/4 inch)
Large backer plate
Large fist clamp
Large fist-clamp bracket
Bolt (1/4 x 5/8 inch)
Bolt (1/4 x 1-1/2 inches)
Bolt (1/4 x 1-1/4 inches)
Small fist clamp
Small backer plate
Carriage bolt (5/16 x 7/8 inch)
Small fist-clamp bracket
Trimmer plate
Nut (5/16 inch)
Channel bracket
Mount plate
Knob
Bolt (3/8 x 7/8 inch)
Nut (3/8 inch)
Carriage bolt (3/8 x 3 inches)
Wide-flange nut (3/8 inch)
No parts required
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
HD Series Riding Mower
CALIFORNIA
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Qty.
–
1
6
1
1
1
2
2
2
1
1
3
1
1
2
1
1
1
2
2
1
1
–
Register at www.Toro.com.
WARNING
Prepare the machine.
Assemble the kit.
Mount the kit to the machine.
Secure a trimmer to the mount assemblies.
Original Instructions (EN)
Form No. 3406-430 Rev B
Installation Instructions
Use
All Rights Reserved *3406-430* B
Printed in the USA
Advertisement
Related Manuals for Toro Titan HD 136-1682
Summary of Contents for Toro Titan HD 136-1682
- Page 1 Carriage bolt (3/8 x 3 inches) Wide-flange nut (3/8 inch) – No parts required Secure a trimmer to the mount assemblies. © 2016—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3406-430* B 8111 Lyndale Avenue South...
-
Page 2: Preparing The Machine
Preparing the Machine 1. Park the machine on a level surface. 2. Move the motion-control levers to the N position. EUTRAL 3. Engage the parking brake. 4. Shut off the engine and remove the key. g037289 g037289 Figure 1 Assembling the Kit 2. - Page 3 g038091 Figure 4 Assembly for Trimmers with a Curved Shaft 1. Knob 7. Small fist clamp 2. Mount plate 8. Small backer plate g038080 Figure 3 3. Trimmer plate 9. Bolt (1/4 x 1-1/4 inch) Assembly for Trimmers with a Straight Shaft 4.
- Page 4 Mounting the Kit to the 2. Install the front mount assembly over the frame, near the right caster wheel, using the wide-flange nut (3/8 Machine inch) and carriage bolt (3/8 x 3 inches) as shown in Figure 1. Install the rear mount assembly to the right side panel on the machine using 2 bolts (3/8 x 7/8 inch) and 2 nuts (3/8 inch) as shown in Figure...
- Page 5 Securing a Trimmer to the Mount Assemblies 1. Secure the rear end of the trimmer to the rear mount assembly using the large fist clamp. 2. Loosen the bolts securing the mount plate to the channel bracket in the front mount assembly (Figure g038088 Figure 7...
- Page 6 Notes:...
- Page 7 Notes:...